Quickstart
This is a
secure
Door Lock - Keypad for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
To add or include the LTA-ML into a Z-Wave network:After installing LTA-ML near the PiACK II, and then connecting to the AC Adapter which is included in the same package:1.Set the controller in inclusion mode.2.Push the pairing button once.3.Wait 5 seconds.4.Confirm the Home Gateway LED of the front panel is on.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
This is the Z-Wave Bridge product to convert BLE into Z-Wave. There has not been such item in Japan and this item is the first item in Japan. This item can bridge our IoT system TAGURI and MIWA Locks electric lock (such as PiACKand DTRS) and allows to open/lock electric lock.
| Reset to factory default |
To factory reset the LTA-ML:1.Confirm the LTA-ML has been already included into a Z-Wave network.2.Remove the AC adapters plug and turn off the LTA-ML.3.Set the AC adapters plug again and wait more than 15 seconds but no longer than 75 seconds.4.Push the pairing button for 10 seconds and the Home Gateway LED turns off.Please use this procedure only when the primary controller is missing or otherwise inoperable. |
| Inclusion |
To add or include the LTA-ML into a Z-Wave network:After installing LTA-ML near the PiACK II, and then connecting to the AC Adapter which is included in the same package:1.Set the controller in inclusion mode.2.Push the pairing button once.3.Wait 5 seconds.4.Confirm the Home Gateway LED of the front panel is on. |
| Exclusion |
To remove or exclude the LTA-ML from a Z-Wave network:1.Set the controller in exclusion mode.2.Push the pairing button 3 times.3.Confirm the Home Gateway LED of the front panel is off. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
1 |
Z-Wave Plus Lifeline |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Door Lock - Keypad |
| Network Operation |
Always On Slave |
| Firmware Version |
HW: 255 FW: 1.00 |
| Z-Wave Version |
6.81.03 |
| Certification ID |
ZC10-19066528 |
| Z-Wave Product Id |
0x0412.0x0001.0x0001 |
| Firmware Updatable |
Updatable by Manufacturer |
| Door Lock Type |
Deadbolt Motor Attachment |
| Controller Supports Multiple Z-Wave Interfaces |
ok |
| Supported Notification Types |
Access Control |
| Outdoor Use |
ok |
| Neutral Wire Required |
ok |
| Gateway Has Preferred Partners |
ok |
| Controller Supports Multiple Networks |
ok |
| Communications Protocol |
Manufacturer's Open/Documented Protocol |
| Communications Connections |
Bluetooth |
| Color |
White |
| IP (Ingress Protection) Rated |
ok |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
