LEEDARSON
Motion Sensor
SKU: 7C-SS-VA-H0
Quickstart
This is a
Add the Motion Sensor into the Z-Wave network:1.Power on your Motion Sensor, and let your Z-Wave controller into add/inclusion mode.2.Implement the button action, the Motion Sensor will send out a node info security CC in command class list (Security inclusion), the LED will be fast blink for 60 seconds.3.If the inclusion is successful, the LED will be turn on within 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This motion sensor is a passive infrared sensor with pet immunity function. This sensor can effectively shield a certain weight of animals to prevent false triggering caused by animal passing. Motion Sensor can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. Motion Sensor is supports the Over-The-Air (OTA) feature for the products firmware upgrade.
| Reset to factory default | Reset Motion Sensor to factory default.NOTE: 1.Triggering this action, in 5 seconds LED will be fast blink. The LED will be turn on within 2 second until hold time is equal to 5 seconds. Motion Sensor will send Device_Reset_Locally to the main controller and exclude from the Z-Wave network when the button is released, this procedure will reset the sensor to factory default.2.Please use this procedure only when the network primary controller is missing or otherwise inoperable. 3.When not in the network, ignore this operation. |
| Inclusion | Add the Motion Sensor into the Z-Wave network:1.Power on your Motion Sensor, and let your Z-Wave controller into add/inclusion mode.2.Implement the button action, the Motion Sensor will send out a node info security CC in command class list (Security inclusion), the LED will be fast blink for 60 seconds.3.If the inclusion is successful, the LED will be turn on within 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above. |
| Exclusion | Remove Motion Sensor from a Z-Wave network:1.Power on your Motion Sensor, and let the Z-Wave primary controller into remove mode.2.Press the button on the Motion Sensor, the LED will be turn on for 60 seconds.3.If Motion Sensor has been successfully removed from your Z-Wave network, the LED will be fast blink 2 seconds. If failed, LED will be turn off forever, and please repeat the steps in above. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline1. Notification Report.Sensor will send Notification Report when Motion Detection Unknown Location and (Event inactive).2. Motion Sensor ReportSensor will send Multilevel Sensor Report (luminance) interval when PIR triggered. 3. Battery Report.Sensor will send Battery Report when the battery level is low and the battery reports value is 0xFF.4. Device Reset Locally. |
| 2 | 5 | Send Basic Set when PIR trigger |
Configuration Parameters
Parameter 10: Low Battery Power Level Low battery power level of alarm threshold values
Low battery power level of alarm threshold values: the value range are 0~50 for percentage, the battery low power level can setting 0%~50%. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 50 | Low battery power level of alarm threshold values |
Parameter 13: Setup the wait time of PIR for clear the motion.
Setup the wait time of PIR for clear the motion.Valid values:5~15300 seconds. Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 5 - 15300 | Setup the wait time of PIR for clear the motion. |
Parameter 14: When the Motion Sensor is triggered, if this parameter is 0x01 then it will send Basic set command to group 1.
When the Motion Sensor is triggered, if this parameter is 0x01 then it will send Basic set command to group 1.0 = Don't send.1 = Send. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | When the Motion Sensor is triggered, if this parameter is 0x01 then it will send Basic set command to group 1. |
Parameter 15: PIR triggers the correspondence between the value of the Basic set and the PIR state.
PIR triggers the correspondence between the value of the Basic set and the PIR state.-If this value is 0x00 :PIR triggers send the basic set with 0xFF, PIR alarm release send the basic set with 0x00.-If this value is 0x01 :PIR triggers send the basic set with 0x00, PIR alarm release send the basic set with 0xFF.Only support 0x00 and 0x01 values as valid value. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | PIR triggers send the basic set with 0xFF, PIR alarm release send the basic set with 0x00. |
| 1 | PIR triggers send the basic set with 0x00, PIR alarm release send the basic set with 0xFF. |
Parameter 16: PIR triggers the correspondence between the value of the Basic set and the PIR stateMotion detection sensitivity level is a value between 1 and 10.
Motion detection sensitivity level is a value between 1 and 10. This value affects the amount of motion energy required to generate a motion event and also affects the detection range and angle.1 = Lowest Motion Sensitivity Size: 1 Byte, Default Value: 9
| Setting | Description |
|---|---|
| 0 - 10 | Motion detection sensitivity level is a value between 1 and 10. 1 = Lowest Motion Sensitivity, 10 = Highest Motion Sensitivity |
Parameter 17: Enable/disable pet immunity mode.
Enable/disable pet immunity mode. This feature is lens dependent and detection range may be reduced when Pet Immunity is enabled.0 = Disable the pet immunity mode1 = Enable the pet immunity mode Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | Enable/disable pet immunity mode.0 = Disable the pet immunity mode,1 = Enable the pet immunity mode |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 2.00 |
| Z-Wave Version | 6.81.04 |
| Certification ID | ZC10-19056522 |
| Z-Wave Product Id | 0x0300.0x0300.0x0026 |
| Sensors | LuminanceMotion/No Motion (Binary) |
| Supported Notification Types | Luminance |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |