Jasco
In-Wall Smart Toggle Switch
SKU: 14319/46563/ZW4009
Quickstart
This is a
1. Follow the instructions for your Z-Wave certifiedcontroller to add a device to the Z-Wave network.2. Once the controller is ready to add your device, press andrelease the top or bottom of the wireless smart switch (rocker).
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
In-Wall Smart Toggle Switch with QuickFit and SimpleWire enhancements. Revolutionary QuickFit design features a housing depth that is up to 20 percent smaller than the previous Z-Wave models. This reduced size coupled with the elimination of heat taps provides a better fit in older style boxes and multi-gang configurations. SimpleWire technology allows line and load to automatically be configured with auto-sensing line-load terminals. All of this is coupled with Z-Wave S2 and Smart Start allows for effortless installation while being safer than ever!
| Reset to factory default | 1. Quickly press ON (top) button three times then immediatelypress the OFF (Bottom) button three times. The LED willflash ON/OFF five times when completed successfully.Note: This should only be used if your networks primarycontroller is missing or otherwise inoperable. |
| Inclusion | 1. Follow the instructions for your Z-Wave certifiedcontroller to add a device to the Z-Wave network.2. Once the controller is ready to add your device, press andrelease the top or bottom of the wireless smart switch (rocker). |
| Exclusion | 1. Follow the instructions for your Z-Wave certified controllerto remove a device from the Z-Wave network.2. Once the controller is ready to remove your device, press andrelease the top or bottom of the wireless smart switch (rocker). |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Supports Basic Set and is controlled by pressing the ON or OFF button with the local load. |
| 3 | 5 | Supports Basic Set and is controlled by double pressing the ON or OFF button. |
Configuration Parameters
Parameter 19: Alternate Exclusion
Default - normal exclusionActive - perform a series of button presses to help eliminate accidental exclusion Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Press any button on the switch |
| 1 | Press two times ON button and two time OFF button, LED will flash 5 times if successful |
Parameter 3: LED Indication Configuration
Configure LED indication to default, invert, always off or always on Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | LED ON when device is OFF, LED is OFF when device is ON |
| 1 | LED ON when device is ON, LED is OFF when device is OFF |
| 2 | LED always OFF |
| 3 | LED Always ON |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.53 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-19056492 |
| Z-Wave Product Id | 0x0063.0x4952.0x3138 |
| Firmware Updatable | Updatable by Consumer by RF |
| Neutral Wire Required | ok |
| Z-Wave Scene Type | Central Scene |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |