This is a
1. Follow the instructions for your Z-Wave certifiedcontroller to add a device to the Z-Wave network.2. Once the controller is ready to add your device, press and releasethe top or bottom of the wireless smart dimmer (rocker).
In-Wall Smart Toggle Dimmer with QuickFit and SimpleWire enhancements. Revolutionary QuickFit design features a housing depth that is up to 20 percent smaller than the previous Z-Wave models. This reduced size coupled with the elimination of heat taps provides a better fit in older style boxes and multi-gang configurations. SimpleWire technology allows line and load to automatically be configured with auto-sensing line-load terminals. All of this is coupled with Z-Wave S2 and Smart Start allows for effortless installation while being safer than ever!
Reset to factory default | 1. Quickly press ON (top) button three times, then immediatelypress the OFF (Bottom) button three times. The LED willflash ON/OFF five times when completed successfully.Note: This should only be used if your networks primarycontroller is missing or otherwise inoperable. |
Inclusion | 1. Follow the instructions for your Z-Wave certifiedcontroller to add a device to the Z-Wave network.2. Once the controller is ready to add your device, press and releasethe top or bottom of the wireless smart dimmer (rocker). |
Exclusion | 1. Follow the instructions for your Z-Wave certified controllerto remove a device from the Z-Wave network.2. Once the controller is ready to remove your device, press andrelease the top or bottom of the wireless smart dimmer (rocker). |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
2 | 5 | Supports Basic Set and is controlled by pressing the ON or OFF button with the local load |
3 | 5 | Supports Basic Set and is controlled by double pressing the ON or OFF button |
Turn your dimmer into an On/Off switch with switch mode Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable normal operation |
1 | Enable switch mode |
Never accidentally remove a device during with alternate exclusion Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Normal operation, press any button on the device |
1 | Press two times ON button and two times OFF button, LED will flash 5 times if exclusion is successful |
Adjust the LED status to default, invert, always OFF or always ON Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | Device is ON, LED is OFF; device is OFF, LED is ON |
1 | Device is ON, LED is ON; device is OFF, LED is OFF |
2 | LED always OFF |
3 | LED always ON |
Set the minimum dimmer threshold Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | Set the minimum dimmer threshold when manually or remotely controlled |
Set the brightness threshold Size: 1 Byte, Default Value: 99
Setting | Description |
---|---|
99 - 1 | Set the maximum brightness threshold when manually or remotely controlled |
Set the default brightness level that the dimmer will turn on when being controlled manually Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Deafult |
1 - 99 | Ex. 1= 1% and 99 = 99% |
Adjust the speed at which the ramps to a specific value other than 0 and FF Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Dim up/down the light to the specified level quickly by command except value 0 and FF |
1 | Dim up/down the light to the specified level slowly by command except value 0 and ff |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 5.53 |
Z-Wave Version | 6.81.03 |
Certification ID | ZC10-19056483 |
Z-Wave Product Id | 0x0063.0x4944.0x3237 |
Z-Wave Scene Type | Central Scene |
Neutral Wire Required | ok |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |