This is a
1) Open the cover.2) Place the device within the direct range of your Z-Wave controller.3) Set the main controller in add mode (see the controllers manual).4) Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast. 5) Wait for the adding process to end.6) Successful adding will be confirmed by the Z-Wave controllers message.
RE.GUARD Water Sensor is a wireless sensor powered by ER14250battery. It is used for detecting water overflowing. It can communicatewith an associated Z-Wave device, such as RE.GUARD Water Control,Siren, Smart Switch, etc.The features list:1) Z-Wave Plus certified for wide compatibility (500 serials product).2) Supports security 0 and security 2 protected mode with AES-128 encryption.3) Contains an extension water detecting probe.4) Temperature measurement.5) The battery life is up to 1 year.6) Support low battery alarm function.7) Support firmware OTA.
Reset to factory default | 1)Power on the device2) Press and hold the Z button for more than 20 seconds3)If holding time more than 20 seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.The reset feature works only when the device has been included into a Z-Wave network.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
Inclusion | 1) Open the cover.2) Place the device within the direct range of your Z-Wave controller.3) Set the main controller in add mode (see the controllers manual).4) Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast. 5) Wait for the adding process to end.6) Successful adding will be confirmed by the Z-Wave controllers message. |
Exclusion | ) Open the cover.2) Place the device within the direct range of your Z-Wave controller.3) Set the main controller remove mode (see the controllers manual).4) Triple click the Z-button quickly, the LED indicator should blink fast.5) Wait for the removing process to end.6) Successful adding will be confirmed by the Z-Wave controllers message. |
NIF | XXXNIF |
Wakeup | Press and hold the Z button for more than 3 seconds and release. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline: 1. Notification Report. Sensor will send Notification Report to the associated nodes 2. Battery Report. Sensor will send Battery Report when the battery level is low and the battery reports value is 0xFF. 3. Device Reset Locally Notification. Sensor will send Device Reset Locally Notification when reset 4.Sensor multilevel report When associated to Group 1, you can adjust the temperature reporting cycle according to the configuration settings. |
2 | 5 | 1. Basic Set. Water Sensor will send Basic Set to associated nodes when Water leak detected. |
Water Sensor can send BASIC SET command to nodes associated with group 2. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Water sensor can reverse its value of BASIC SET when flooding is triggered. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send BASIC SET VALUE = 255 to nodes associated with group 2 when flooding alarm is triggered. Send BASIC SET VALUE = 0 to nodes associated with group 2 when flooding alarm is canceled. |
1 | Send BASIC SET VALUE = 0 to nodes associated with group 2 when flooding alarm is triggered. Send BASIC SET VALUE = 255 to nodes associated with group 2 when flooding alarm is canceled. |
How much time interval is reported by flooding alarm. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
1 - 240 | The higher the value, the long the report periodically - in decimal values from 1 to 240 |
The sensor measures the temperature every ten minutes, change of 1 degree Celsius will be reported. By default, it must report at least once a day. Size: 1 Byte, Default Value: 144
Setting | Description |
---|---|
3 - 240 | the higher the value ,the long the report time |
The accuracy is 0.1 degrees, the United States uses Fahrenheit, and the Fahrenheit temperature range is -670~2570, which is -67.0~257.0F. Other countries use Celsius temperature, Celsius temperature range -550~1250, which is -55.0~125.0 C. Size: 2 Byte, Default Value: 400
Setting | Description |
---|---|
-670 - 2570 | the larger the value , the higher the high temperature(US) |
-550 - 1250 | the larger the value , the higher the high temperature(other) |
The accuracy is 0.1 degrees, the United States uses Fahrenheit, and the Fahrenheit temperature range is -670~2570, which is -67.0~257.0F. Other countries use Celsius temperature, Celsius temperature range -550~1250, which is -55.0~125.0 C. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
-670 - 2570 | the smaller the value , the lower the low temperature(US) |
-550 - 1250 | the smaller the value , the lower the low temperature(other) |
Whether the light flashes when the alarm occurs. when the value is 0, the product will not alarm when being triggered; when the value is 1, the product will alarm when being triggered Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
The low voltage alarm threshold corresponds to the amount of power, the unit is the percentage of power, the value range is 10~50, other values are invalid, that is, the power corresponding to the low voltage can be configured to be 10% to 50%. Size: 1 Byte, Default Value: 20
Setting | Description |
---|---|
10 - 50 | Set the trigger value for the low battery alarm |
Hardware Platform | ZM5202 |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 1 FW: 1.03 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-19056475 |
Z-Wave Product Id | 0x0413.0x021a.0x0002 |
Firmware Updatable | Updatable by Consumer by RF |
Color | White |
Supported Notification Types | Heat AlarmHome SecurityWater Alarm |
Sensors | Air Temperature |
Frequency | Russia - 868.4MHz, 869.85MHz |
Maximum transmission power | 5 mW |