Simon
S100 Rocker for Dimmer (China)
SKU: 10003020-13X
Quickstart
This is a
When the pushbutton is released after a press of (2sec
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Simon iO Dimmer is integrated by Electronic Dimmer and a Rocker,that provides Z-Wave communication attributes. The touch surface offers an slider area in order to adjust the light level showing the dimming intensit y with 7 LEDs . Simon iO Dimmer is ready to operate with Z-Wave controllers and configured to be managed by Simon100 IO APP using the HUB plug IO for getting a better user experience.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
When the pushbutton is released after a press of (30sec
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
When the pushbutton is released after a press of (2secExclusion
When the pushbutton is released after a press of (2secQuick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 3 | Z-Wave Plus Lifeline- On -> CC Basic, Basic Report, Value 0x01 - 0x63 Report the dimming level- Off -> CC Basic, Basic Report, Value 0x00Instant Power Consumption vary over 10% and is stable almost 2sec- CC Meter, Meter Report, Electric meter, Consumed, Watts, Size 4, Precision 1, Value (W)Calibration requirement change. (If device needs to be calibrated and is Added into a Z-Wave network, it will report after receive an Association Set of life line).- Calibration required -> CC Configuration, Configuration Report, Param 23, Value 0xFF- Calibration not required -> CC Configuration, Configuration Report, Param 23, Value 0x00After reset the Z-Wave module, a DEVICE-RESET-LOCALLY-NOTIFICATION is sent. |
| 2 | 20 | CtrlOn/Off Report when load state is changed:- On -> CC Basic, Basic Report, Value 0x01 - 0x63 Report the dimming level- Off -> CC Basic, Basic Report, Value 0x00 |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Association LED
Allows to turn ON or OFF the central LED Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Turns the LED OFF |
| 1 - 255 | Turns the central LED ON |
Parameter 10: Delay ON
Sets the delay time to turn on the light Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Instantly. Disable timming |
| 1 - 127 | 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution |
| 128 - 254 | 1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution |
Parameter 11: Activation time
Sets the time the light stays on. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Instantly. Disable timming |
| 1 - 127 | 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution |
| 128 - 254 | 1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution |
Parameter 12: Behavior of LED in repose
Sets the central led ilumination when the key is in repose state Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | LED OFF |
| 1 - 255 | Central LED on at 20% of maximum level |
Parameter 13: Lock input
Lock or Unlock the direct control of the load Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unlock the direct control of load |
| 1 - 255 | Lock the direct control of load |
Parameter 15: Reset default
Resets groups, Z-Wave status, and some or all configurations depending on the configuration value (write only) Size: 1 Byte, Default Value: 39015
| Setting | Description |
|---|---|
| 39015 | Parameters, Groups, and Z-Wave status are restored to default. |
| 17170 | Parameters, Groups, and Z-Wave status are restored to default. |
Parameter 16: Delay OFF
Sets the delay time to turn off the light Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Instantly. Disable timming |
| 1 - 127 | 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution |
| 128 - 254 | 1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution |
Parameter 19: Press action
Controls the behavior of the product when the key is pressed Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | When short press, the device toggles the load. The Slider does not work. |
| 1 | When short press, the device turns ON the load. The Slider does not work |
| 2 | When short press, the device turns OFF the load. The Slider does not works |
| 4 | When short press, the device turns ON the load. When hold press from 2seconds to 10seconds device turns OFF the load. The Slider does not works with this configuration, the device will not send the Node Info neither Show the LEDs feedback with this press action. The Slider does not work |
| 5 | When short press, the device toggles the load. The Slider dims the load when it is ON |
Parameter 20: Identify
Allows to identify a product using its central LED (write only) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 255 | the central LED blinks for 5 seconds in order to identify the device |
Parameter 21: State of charge
Reports the state of the charge (read only) Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 45056 | Load is OFF |
| 45057 | Load is ON |
| 45312 - 45411 | Last active dimming value |
Parameter 23: Calibration required
Reports if calibration is required or not (read only) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Calibration is not required |
| 255 | It is necessary to calibrate the dimmer to work properly |
Parameter 27: Lock long press
Locks or unlocks the long press on the key Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Long press works as described previously |
| 255 | Long press of from 2 seconds to 10 seconds does not send a the Node Info. Long press of t>30s Parameters, except Lock long press are restored to default and device send a Node Info. |
Parameter 4: Set time
Sets the time it takes to turn on the light (ramp time) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Instantly. Disable timming |
| 1 - 127 | 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution |
| 128 - 254 | 1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution |
Parameter 5: Fade time
Sets the time it takes to turn off the light (ramp time) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Instantly. Disable timming |
| 1 - 127 | 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution |
| 128 - 254 | 1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution |
Parameter 6: Min dimming value
Sets the minimun dimming value Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 98 | Once the devices gets a value through Z-Wave it Scales the value read according this minimum margin |
Parameter 7: Max dimming value
Sets the maximum dimming value Size: 1 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 2 - 99 | Once the devices gets a value through Z-Wave it Scales the value read according this maximum margin |
Parameter 8: Last on value
Returns or sets the last non zero dimming value. In case of Set the device turns ON the load. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 127 | returns or sets the last non zero dimming value. In case of Set the device turns ON the load |
Parameter 9: Calibration
Performs a device calibration Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Device performs calibration using Trailing and leading Edge and decides which one is better |
| 2 | Device performs calibration using Trailing and leading Edge and decides which one is better |
| 3 | Device is calibrated using Leading Edge |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 4.24:78.59:70.48 |
| Z-Wave Version | 6.51.07 |
| Certification ID | ZC10-19046438 |
| Z-Wave Product Id | 0x0267.0x0007.0x0000 |
| Firmware Updatable | Updatable by Professional/Technician |
| Supported Meter Type | Electric Energy |
| Electric Load Type | Dimmable ELV (Magnetic)Dimmable LEDDimmable MLV (Magnetic)Incandescent |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info V3
- Association V2
- Basic
- Configuration V2
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Meter V4
- Powerlevel
- Switch Multilevel V3
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.