Philio Technology
Smart Dimmer Plug
SKU: PAD09-2
Quickstart
This is a
1.check Z-WaveTM Controller entered inclusion mode.2.Pressing Include button of PAD09 three times within 2 seconds will enter inclusion mode.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Dimmer Plug is designed to control the on/off status of lighting in your house. The unit also provides dimmer function which is only applicable to light bulbs. At 220-240V voltage, this Dimmer Plug can support connected load of Max. 200W. To manually switch on the light, press and release the On/Off dimmer button when the light is off. The light will dim from off to the level which was set before switch off. To manually switch off the light, press and release the On/Off button shortly when the light is on. To adjust the dim level, press and hold the On/Off button until the desired dim level is achieved, then release.
| Reset to factory default | 1. Pressing Include button of PAD09 three times within 2 seconds will enter inclusion mode. 2. Within 1 second, press Include button of PAD09 again for 5 seconds. 3. IDs are excluded. note : Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion | 1.check Z-WaveTM Controller entered inclusion mode.2.Pressing Include button of PAD09 three times within 2 seconds will enter inclusion mode. |
| Exclusion | 1.check Z-WaveTM Controller entered exclusion mode.2.Pressing Include button of PAD09 three times within 2 seconds will enter exclusion mode. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1 name:LifenameGroup 1 command list:COMMAND_CLASS_SWITCH_MULTILEVEL_V2,COMMAND_CLASS_NOTIFICATION_V8,COMMAND_CLASS_DEVICE_RESET_LOCALLY |
| 2 | 5 | Group 2 name:Control Key1Group 2 command list:COMMAND_CLASS_BASIC_SET, |
Configuration Parameters
Parameter 1: Dimmer LevelReport mode
Whenever dimmer on/off state changes, it will send MULTILEVEL_SWITCH_REPORT to the nodes of group1. The default setting is Enable the function. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | 0 : Disable1 : Enable |
Parameter 2: LEDindicationmode
Show dimmer StateWhen dimmer is on, LED is on. When dimmer is off, LED is off. The default setting is Show dimmer State. Show Night modeWhen dimmer is on, LED is off. When dimmer is off, LED is on. One flash modeWhen dimmer on/off state changes, LED will light on one second and then off. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 3 | 1: Show dimmer state2 : Show night mode3: One flash mode |
Parameter 4: Restoredimmer state
Whenever the AC power return from lost, PAD09 will restore the switch state which could be Dimmer offLast dimmer stateDimmer on. The default setting is Last dimmer state. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 2 | 0 : Dimmer off1 : Last dimmer state2 : Dimmer on |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.01 |
| Z-Wave Version | 6.81.01 |
| Certification ID | ZC10-18126330 |
| Z-Wave Product Id | 0x013C.0x0005.0x0060 |
| Firmware Updatable | Updatable by Manufacturer |
| Supported Notification Types | Power Management |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |