Quickstart
This is a
secure
On/Off Power Switch for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
NOTE: Before beginning the network add procedure, ensure there are no devices plugged into either receptacle outlet. After the device has ben successfully added to the network, DO NOT plug anything into either receptacle outlet for at least 2 minutes to allow the module time to synchronize with the outlet metering hardware, or the accuracy of your meter readings may be adversely affected.1.Follow network ADD steps for your Z-Wave controller/hub to prepare the network to accept a device addition.2.Lightly press the push button on the Swidget Z-Wave Insert and hold for 10-15 seconds until the LED illuminates solid blue, then release the button. The LED will flash blue to indicate ADD mode is enabled. No manual or external Z-Wave operations are possible during this activity.3.The Swidget Z-Wave Insert will remain in ADD mode for up to 60 seconds. If the device is successfully added to the Z-Wave network, the LED will be solid blue for 5 seconds then return to the normal operational state; LED will be solid green if switch is ON (default), LED will not be illuminated if switch is OFF. If the device fails to be successfully added to the network after 60 seconds, the red LED will begin to flash. If necessary, consult your Z-Wave controller/hub manual and re-try. 4.Please see section 4.4 on how to perform a local device reset if multiple remove attempts fail.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
The Swidget Z-Wave Insert can control your appliances, lights, or whole home when paired with a Swidget Outlet. The user can wirelessly connect to any compatible Z-Wave hub or device to control one outlet and independently monitor power consumption of both outlets.Easily installed, the Swidget Outlet functions like an ordinary outlet with the ability to add Smart Homefunctionality, like the Z-Wave Control, through the center cavity.Once connected to a compatible Z-Wave hub, this Z-Wave Control Insert contains the smarts to schedule your devices to turn on/off at a specified time, event or activity. If supported by your hub, it can send you notifications when a plugged-in device turns on/off like your sump pump or garage door opener, and it can display power consumption of both outlets to save you money and power over time.Features: One controlled AC receptacle Remote ON/OFF control viaZ-Wave Controller/Hub Manual ON/OFF of controlled receptacle via front panel push button One always on AC receptacle Independent power monitoring of both AC receptacles Swidget Z-Wave Device detected as:o Meter (always ON receptacle)o Switch + Meter CONTROLLED receptacle
| Reset to factory default |
To perform a local device reset, lightly press and hold the push button on the Swidget Z-Wave Insert for approximately 20 seconds until the LED turns SOLID RED, and then release. After 10 seconds the LED will illuminate SOLID BLUE; indicating user is passing through network add/remove period.After 15 seconds elapsed hold time, the LED will turn offAfter 20 seconds elapsed hold time, the LED will turn SOLID RED; indicating that the user has entered the device reset period. Releasing the button during this period triggers the Factory Default Local Reset operations.When the Reset operation is in progress, the LED will progress from green to blue to red repeatedly until the reset process is complete, after which the LED will be turned OFF.If the user continues to hold the button, after 25 seconds elapse, the user will leave the device reset period, the LED will turn OFF, and no actions will be taken when the button is released.NOTE: The local reset procedure should only be used when the original controller is inoperable or has been replaced, or if Network Add or Network Remove operations have failed after a few attempts.Resetting to factory default settings will, reset the Swidget Z-Wave 500 Series Insert network parameters to the default removed state, and delete the Lifeline Association if it exists. |
| Inclusion |
NOTE: Before beginning the network add procedure, ensure there are no devices plugged into either receptacle outlet. After the device has ben successfully added to the network, DO NOT plug anything into either receptacle outlet for at least 2 minutes to allow the module time to synchronize with the outlet metering hardware, or the accuracy of your meter readings may be adversely affected.1.Follow network ADD steps for your Z-Wave controller/hub to prepare the network to accept a device addition.2.Lightly press the push button on the Swidget Z-Wave Insert and hold for 10-15 seconds until the LED illuminates solid blue, then release the button. The LED will flash blue to indicate ADD mode is enabled. No manual or external Z-Wave operations are possible during this activity.3.The Swidget Z-Wave Insert will remain in ADD mode for up to 60 seconds. If the device is successfully added to the Z-Wave network, the LED will be solid blue for 5 seconds then return to the normal operational state; LED will be solid green if switch is ON (default), LED will not be illuminated if switch is OFF. If the device fails to be successfully added to the network after 60 seconds, the red LED will begin to flash. If necessary, consult your Z-Wave controller/hub manual and re-try. 4.Please see section 4.4 on how to perform a local device reset if multiple remove attempts fail. |
| Exclusion |
1.Follow network REMOVE steps for your Z-Wave controller/hub.2.Lightly press the push button on the Swidget Z-Wave Insert and hold for approximately 10 seconds until the LED illuminates solid blue, then release the button. The LED will flash blue to indicate REMOVE mode is enabled.3.The Swidget Z-Wave Insert will remain in REMOVE mode for up to 60 seconds. If the device is successfully removed from the Z-Wave network, the LED will be solid blue for 5 seconds then return to the normal operational state. If the device fails to be successfully removed from the network after 60 seconds, the red LED will begin to flash. If necessary, consult your Z-Wave controller/hub manual and re-try.4.Please see section 4.4 on how to perform a local device reset if multiple remove attempts fail. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
1 |
Z-Wave Plus LifelineDevice Reset Locally is sent on completion of device local reset operation.After calibration, a METER_REPORT_V2 is sent every 60 seconds, for the controlled outlet for a non-multi-channel association, or for BOTH the controlled and always-on outlet for a multi-channel association.Meter report contains electricity consumed in Watts :Rate Type0x01Import (consumed)Meter Type0x01Electric meterPrecision0x02Number of decimal places in meter valueScale0x02WattsSize0x044-byte reportMeter Value Byte 1 (MSB)0xXXMSB of 32-bit meter valueMeter Value Byte 20xXXmeter value dataMeter Value Byte 30xXXmeter value data Meter Value Byte 4 (LSB)0xXXLSB of 32-bit meter valueDelta Time 10x00No previous meter data includedDelta Time 20x00No previous meter data includedMeter reports for the controlled outlet are sent from the ROOT for NODE associations.Meter reports for both the controlled outlet AND the always-on outlet aresent from the endpoint 1, and endpoint 2 when the association destination is set as a multi-channel association. |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
On/Off Power Switch |
| Network Operation |
Always On Slave |
| Firmware Version |
HW: 2 FW: 6.01:01.02 |
| Z-Wave Version |
6.81.01 |
| Certification ID |
ZC10-18126328 |
| Z-Wave Product Id |
0x0345.0x0001.0x0001 |
| Color |
White |
| Supported Meter Type |
Electric Energy |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
