Zooz
Z-Wave Plus Double Plug
SKU: ZW47
Quickstart
This is a
Inclusion the ZW47 from the existing Z-Wave home control network with your primary controller.---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.---When prompted by your primary controller, click the PROG button Three times in one second.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
It is smart plug type device controlled by Z-Wave controller and can be configured in Z-Wave sensor network, if Z-Wave certified controller features remote access, you can dim lights at home from your mobile phone separately, and manual dim light by push button .
| Reset to factory default | Press the button twice quickly and then press and hold the button 10S.device will resetPlease use this procedure only when the network primary controller is missing or otherwise inoperable |
| Inclusion | Inclusion the ZW47 from the existing Z-Wave home control network with your primary controller.---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.---When prompted by your primary controller, click the PROG button Three times in one second. |
| Exclusion | Exclusion the ZW47 from the existing Z-Wave home control network with your primary controller.---Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.---When prompted by your primary controller, click the PROG button Three times in one second. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
| 2 | 5 | basic set commandWhen the output of the ZW47 Enpoint1 socket is changed, On (0xFF) or Off (0x00)orOverload, The ZW47 will automatically send out a relatedbasic set command. On (0xFF) or Off (0x00) to its associated group. |
| 3 | 5 | basic set commandWhen the output of the ZW47 Enpoint2 socket is changed, On (0xFF) or Off (0x00)orOverload, The ZW47 will automatically send out a relatedbasic set command. On (0xFF) or Off (0x00) to its associated group. |
Configuration Parameters
Parameter 1: Restores state after power failure
Restores state after power failure Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The state before a power outage. |
| 1 | outlet on |
| 2 | outlet off |
Parameter 10: Endpoint1 Enable Auto Turn-ON Timer
Endpoint1 Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP1 Auto Turn-ON Timer Disabled |
| 1 | EP1 Auto Turn-ON Timer Enabled |
Parameter 11: Endpoint1 Count Down Configuration(Turn on the output by time
Endpoint1 Count Down Configuration(Turn on the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint1 Count Down Configuration(Turn on the output by time |
Parameter 12: Endpoint2 Enable Auto Turn-OFF Timer
Endpoint2 Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP2 Auto Turn-OFF Timer Disabled |
| 1 | EP2 Auto Turn-OFF Timer Enabled |
Parameter 13: Endpoint2 Count Down Configuration(Turn off the output by time
Endpoint2 Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint2 Count Down Configuration(Turn off the output by time |
Parameter 14: Endpoint2 Enable Auto Turn-ON Timer
`Endpoint2 Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP2 Auto Turn-ON Timer Disabled |
| 1 | EP2 Auto Turn-ON Timer Enabled |
Parameter 15: Endpoint2 Count Down Configuration(Turn on the output by time
Endpoint2 Count Down Configuration(Turn on the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint2 Count Down Configuration(Turn on the output by time |
Parameter 16: Manual Control
Manual Control Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Manual Control Disabled |
| 1 | Manual Control Enabled |
Parameter 17: Status LED Configuration
Status LED Configuration Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED indicator will display power consumption whenever the device is plugged in |
| 1 | LED indicator will display power consumption whenever the device is ON in and will turn off when the plug is OFF |
| 2 | LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off |
| 3 | Always OFF |
Parameter 2: Power Wattage Report Value Threshold(Wattage)
Power Wattage Report Value Threshold(Wattage) Size: 4 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 10 | Power Wattage Report Value Threshold(Wattage) |
Parameter 4: Energy (kWh) Report Frequency (Timer)
Energy (kWh) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Energy (kWh) Report Frequency (Timer) |
Parameter 5: Voltage (V) Report Frequency (Timer)
Voltage (V) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Voltage (V) Report Frequency (Timer) |
Parameter 6: Electricity (A) Report Frequency (Timer)
Electricity (A) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 0 - 30 | Power Wattage Report Value Threshold(Wattage) |
| 30 - 2678400 | Electricity (A) Report Frequency (Timer) |
Parameter 7: Overload Protection (Current)
Overload Protection (Current) Size: 1 Byte, Default Value: 13
| Setting | Description |
|---|---|
| 1 - 16 | Overload Protection (Current) |
Parameter 8: Endpoint1 Enable Auto Turn-OFF Timer
Endpoint1 Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | EP1 Auto Turn-OFF Timer Disabled |
| 1 | EP1Auto Turn-OFF Timer Enabled |
Parameter 9: Endpoint1 Count Down Configuration(Turn off the output by time
Endpoint1 Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint1 Count Down Configuration(Turn off the output by time |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 1.00 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18116324 |
| Z-Wave Product Id | 0x0312.0xA000.0xA003 |
| Electric Load Type | FluorescentIncandescentInductive (e.g. Motor)LED |
| Color | White |
| Supported Meter Type | Electric Energy |
| Firmware Updatable | Updatable by Consumer by RF |
| Supported Notification Types | Power Management |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |