Quickstart

This is a secure Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * CR2 batteries. To run this device please make sure the internal battery is fully charged.
A.) Slide the base unit from the mounting plate and remove the safety strip from the battery compartment.
B.) Click the + (Add) button in your Z-Wave App and follow the further instructions
C.) Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The ABUS Z-Wave Magnetic contact detects when windows and doors are opened and notifies your Z-Wave gateway. Thanks to battery operation and adhesive mounting pad the installation it can be installed quickly and simple. The Magnetic contact is protected against sabotage via a tamper switch. Battery life is up to 3 years.

Installation

Test the release behaviour at the desired mounting position in advance.

The magnet should be mounted no more than 15 mm from the sensor.

Note:

Do not mount the detector...

...on or near metal surfaces!

...in close proximity (< 1m) to gas, water and power lines!

...near electrical devices e.g. PC, copier or other transmitters

Installation site:

Optimum mounting location for the door, window contact is the upper corner of your window or door frame.

Remove the adhesive strip cover from the sensor and magnets and attach it to the desired mounting position.

The magnet can be mounted to the right or left of the sensor.

Center the magnet on the sensor (see marking strip).

When the sensor is opened or closed, the status LED lights up once.

Product Usage

1. Sensor
2. Magnet
3. Status - LED
4. Tamper Button
5. Battery case

Reset to factory default	Press and hold the tamper button while inserting the battery.
Inclusion	A.) Slide the base unit from the mounting plate and remove the safety strip from the battery compartment. B.) Click the + (Add) button in your Z-Wave App and follow the further instructions C.) Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times.
Exclusion	A.) Click the - (Remove) button in your Z-Wave App and follow the further instructions. B.) Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times.
NIF	XXXNIF
Wakeup	-Wake up Notification is transmitted every 24 hours by default.-Wake up Notification is transmitted after Notification Report is transmitted
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	5	Lifeline
2	5	Sensor - Binary Sensor
3	5	Tamper - Binary Sensor
4	5	Sensor - Notification report
5	5	Tamper - Notification Report

Technical Data

Dimensions	37 x 72 x 22 mm
Weight	32 gr
Hardware Platform	ZM5101
EAN	4003318841491
IP Class	IP 20
Voltage	3V
Battery Type	1 * CR2
Device Type	Notification Sensor
Network Operation	Reporting Sleeping Slave
Z-Wave Version	6.71.03
Certification ID	ZC10-18116318
Z-Wave Product Id	0x0403.0x0002.0x0000
Color	White
Communications Protocol	Z-Wave Serial API
Firmware Updatable	Not Updatable
Outdoor Use	ok
Sensors	Open/Closed (Binary)
Supported Notification Types	Emergency AlarmHome Security
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

ABUS

ABUS Z-Wave Magnetic Contact