Everspring
Metering Plug
SKU: AN188-2
Quickstart
This is a
1. Put the Z-Wave Controller into inclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The AN188 is a miniature size on/off and metering plug to control lighting and appliances. It is possible to turn on/off home devices and check the status directly from a smartphone.Compact in design, yet certified for safety by makes it suitable for plugging into any power outlet. The metering plug can support wattage, voltage, ampere, and measurement. The unit can also detect overload upon which the unit will switch off relay and keep LED flashing until power is off and re-applied.
| Reset to factory default | 1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds).3. Node ID is excluded.The device reverts to factory default state and will be in auto-inclusion mode for 25 secs.(Use this procedure only in the event that the network primary controller is missing, or otherwise inoperable.) |
| Inclusion | 1. Put the Z-Wave Controller into inclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. |
| Exclusion | 1. Put the Z-Wave Controller into exclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
| 2 | 4 | On/Off Control |
Configuration Parameters
Parameter 1: Set Basic Set Command value
Basic Set Command value can be set 0~99, 255 Size: 2 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 - 99 | Basic Set Command value |
| 255 | 0xFF |
Parameter 2: Set the delaying time to report to Group 1
Value of the delaying time to report to Group 1 can be set 3~25 seconds Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 3 - 25 | Delaying time to report to Group 1 |
Parameter 3: Set whether to remember the last status
1: remember0: do not remember Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | remember or not remember the last status |
Parameter 4: Set the interval for wattage auto report
Value of the interval for wattage auto report can be set 1~32767 minutes. Size: 2 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 32767 | The interval for wattage auto report |
Parameter 5: Set the interval for kW*h auto report
Value of the interval for kW*h auto report can be set 1~32676 minutes. Size: 2 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 32676 | The interval for kW*h auto report |
Parameter 6: Auto report when load surpasses the set value of wattage
Value can be set 0~3500W Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 3500 | 0: does not report automatically |
Parameter 7: Auto report when the change of wattage surpasses the set percentage
Value can be set 0~100% Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 100 | 0: does not report automatically |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00:00.04 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18106289 |
| Z-Wave Product Id | 0x0060.0x0004.0x000D |
| Firmware Updatable | Updatable by Consumer via Internet |
| Color | White |
| Supported Notification Types | Power Management |
| Supported Meter Type | Electric Energy |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |