Faultless
Electronic Z-Wave Deadbolt
SKU: A15-WG014-S2
Quickstart
This is a
1. Press [SET] for 1 second 2. Enter 4 -8 digits programing Code3. Press the buttons #90# 4. Include successfully (beep * 1)/ unsuccessfully (beep x 3)
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Great Convenience Touch to activate, touch to lock Connect your Z-Wave smart home system and operate from anywhere Holds up to 25 user codes Holds up to 4 single-entry codes Vacation mode (deactivates all user codes temporarily) Auto-lock with adjustable delay (10 - 99 seconds) Back-up mechanical keyway Uncompromised Security ANSI Grade 2 qualitydeadbolt operates over 150,000 times ANSI A156.25 compliant - resistant to dust, rain, and corrosion under variable temperatures 4-digit random guiding code prevents code-probing Touch screen is temporarily disabled after 4 consecutive incorrect entries Easy Installation Easy installation with a Philips screwdriver Fits most standard door preparations Online video instruction available (please scan the QR code on this box)
| Reset to factory default | 1. Remove one battery2. Press and hold SET button while inserting the battery back.Hold the set button until long beep has finished.3. Restoring the lock to factory settings will remove its connection to your network and clear all devices from its association group. The reset procedure should only be used when the primary controller is missing or inoperable.4.Please re-enter the default Programming Code to set up the lock after restoring to factory settings. |
| Inclusion | 1. Press [SET] for 1 second 2. Enter 4 -8 digits programing Code3. Press the buttons #90# 4. Include successfully (beep * 1)/ unsuccessfully (beep x 3) |
| Exclusion | 1. Press [SET] for 1 second 2. Enter 4 -8 digits programing Code3. Press the buttons #90# 4. Exclusion successfully (beep * 1) /unsuccessfully (beep x 3) |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline; A NOTIFICATION frame is sent to the nodes in this association group when a lifeline event occurs. |
Configuration Parameters
Parameter 1: Guiding code on/off
Value 0X00=off0x01=on Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | 0X00=off 0x01=on |
Parameter 2: vacation mode on/off
Value 0X00=off0x01=on Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0X00=off 0x01=on |
Parameter 3: volume on/off
Value 0X00=off0x01=on Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | 0X00=off 0x01=on |
Parameter 4: auto-lock on/off
Value 0X00=off0x01=on Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0X00=off 0x01=on |
Parameter 5: auto lock timer 10-99
Value 0X0A~0X63 =10~99seconds Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 10 - 99 | 0X0A~0X63 =10~99seconds |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Door Lock - Keypad |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 255 FW: 3.01:01.01 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18096240 |
| Z-Wave Product Id | 0x0262.0x0004.0x0002 |
| Outdoor Use | ok |
| Door Lock Type | Deadbolt |
| Supported Notification Types | Access ControlPower Management |
| Firmware Updatable | Updatable by Manufacturer |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |