Qolsys Inc.
IQ Outlet Plug-In On/Off Switch
SKU: QZ2130-840
Quickstart
This is a
Inclusion: Add the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add the IQ Outlet into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added using the traditional method for Z-Wave as follows:1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was added successfully.3. Once the IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.If the controller shows it failed, repeat the procedure.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Qolsys' IQ Outlet is a Z-Wave Plus certified device with S2 security and SmartStart. The IQ Outlet can be used to turn On or Off lamps or AC operated appliances. Each Z-Wave device also serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range.Additional Features: Works with incandescent, CFL & LED lights & appliances Plugs into Standard AC outlet Remotely or manually turns ON or OFF lights LED backlit On/Off button Control lights or appliances via schedule or remotely Second wall AC outlet remains free Works with any gateway supporting Z-Wave
| Reset to factory default | 1. Unplug the IQ Outlet from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)2. Press and hold the button on the IQ Outlet3. Plug the IQ Outlet back into the AC outlet with the button pressedAfter 3 seconds, release the button. If you see the button blink, that means that IQ Outlet has been reset successfully.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion | Inclusion: Add the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add the IQ Outlet into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added using the traditional method for Z-Wave as follows:1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was added successfully.3. Once the IQ Outlet has been successfully added to your home network, you can move it to the preferred location in the home.If the controller shows it failed, repeat the procedure. |
| Exclusion | Exclusion: Remove the device into your network by a Z-Wave certified controller. The IQ Outlet supports the latest S2 security and SmartStart offered by Z-Wave certified controllers. If your controller supports S2 or SmartStart, please refer to the user guide of the controller for detailed instructions on removing devices to the network. In addition, the device can be removed using the traditional method for Z-Wave as follows:1. Place your network controller into Exclusion mode by following the controller manufacturer's instructions.2. When the controller is ready, single click the button on the front of the IQ Outlet. The controller should indicate that the new device was removed successfully.If the controller shows it failed, repeat the procedure. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | 1. Z-Wave Plus Lifeline2. Device Reset Locally Notification |
Configuration Parameters
Parameter 3: Night Light
The LED indicator will be OFF when the connected light is ON and vice versa.When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 50.03 |
| Z-Wave Version | 6.81.00 |
| Certification ID | ZC10-18086208 |
| Z-Wave Product Id | 0x012A.0x4447.0x3031 |
| Color | White |
| Switch Type | Push Button Illuminated |
| Firmware Updatable | Updatable by Consumer by RF |
| Outdoor Use | ok |
| Electric Load Type | FluorescentIncandescentLED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |