COQON

Energy Consumption Monitor Energiemonitor Z-Wave, 230VModel Number

SKU: EMHTZ001

ZWave+ Security V2

Quickstart

This is a secure Sub Energy Meter for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
1. Start the COQON App2. Select "Device" then "Settings" and tap on "+" to add your Electric Monitor3. Select "Add new COQON device" 4. Follow the steps in the App



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

The power monitor measures and registers power consumption to help users understand their energy consumption. The measurement takes place per circuit. This information may be useful for those who want to reduce their energy consumption or use energy-efficient behavior.They provide insights into areas in their home where more energy is consumed than in others.Product Compliance:This product meets the essential requirements of (RED) 2014/53 / EU and 2011/65 / EU. The full text of the EU Declaration of Conformity can be found on www.coqon.de.Technical specifications:Model no. EMHTZ001Mains voltage230V, 50 HzAmbient temperature0-45CDimensions100x100x31mmRadio language Z-Wave Plus
Reset to factory default To reset the device to factory default press and hold the function button for 10 seconds. Note: Please use this procedure ony when the network primary controller is missing or otherwise inoperabe!
Inclusion 1. Start the COQON App2. Select "Device" then "Settings" and tap on "+" to add your Electric Monitor3. Select "Add new COQON device" 4. Follow the steps in the App
Exclusion 1. Start the COQON App2. Select "Device" then "Settings" and tap on the device to remove Electric Monitor3. Tap on the the trash can icon4. Follow the steps in the App
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 10: Clamp 1

Percentage change in wattage to induce an automatic report (Clamp 1)
Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid values 0-100

Parameter 101: Auto report KWh

Auto report KWh
Size: 1 Byte, Default Value: 1

Setting Description
0 - 31 Valid values 0 - 31, Bit 0: Whole EM, Bit 1: Clamp 1, Bit 2: Clamp 2, Bit 3: Clamp 3, Bit 4: Clamp 4

Parameter 102: Auto report W

Auto report W
Size: 1 Byte, Default Value: 1

Setting Description
0 - 31 Valid values 0 - 31, Bit 0: Whole EM, Bit 1: Clamp 1, Bit 2: Clamp 2, Bit 3: Clamp 3, Bit 4: Clamp 4

Parameter 103: Auto report V

Auto report V
Size: 1 Byte, Default Value: 0

Setting Description
0 - 31 Valid values 0 - 31, Bit 0: Whole EM, Bit 1: Clamp 1, Bit 2: Clamp 2, Bit 3: Clamp 3, Bit 4: Clamp 4

Parameter 104: Auto report A

Auto report A
Size: 1 Byte, Default Value: 0

Setting Description
0 - 31 Valid values 0 - 31, Bit 0: Whole EM, Bit 1: Clamp 1, Bit 2: Clamp 2, Bit 3: Clamp 3, Bit 4: Clamp 4

Parameter 105: Auto report kVar

Auto report kVar
Size: 1 Byte, Default Value: 0

Setting Description
0 - 31 Valid values 0 - 31, Bit 0: Whole EM, Bit 1: Clamp 1, Bit 2: Clamp 2, Bit 3: Clamp 3, Bit 4: Clamp 4

Parameter 11: Clamp 2

Percentage change in wattage to induce an automatic report (Clamp 2)
Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid values 0-100

Parameter 111: Time interval Auto report kWh

The Time interval of Auto report kWh
Size: 4 Byte, Default Value: 0

Setting Description
0 - 1 Valid values 0x1E-0x7FFFFFFF

Parameter 112: Time interval Auto report W

The Time interval of Auto report W
Size: 4 Byte, Default Value: 0

Setting Description
0 - 1 Valid values 0x1E-0x7FFFFFFF

Parameter 113: Time interval Auto report V

The Time interval of Auto report V
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 Valid values 0x1E-0x7FFFFFFF

Parameter 114: Time interval Auto report A

The Time interval of Auto report A
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 Valid values 0x1E-0x7FFFFFFF

Parameter 115: Time interval Auto report kVar

The Time interval of Auto report kVar
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 Valid values 0x1E-0x7FFFFFFF

Parameter 12: Clamp 3

Percentage change in wattage to induce an automatic report (Clamp 3)
Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid values 0-100

Parameter 13: Clamp 4

Percentage change in wattage to induce an automatic report (Clamp 4)
Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid values 0-100

Parameter 2: Energy detection mode

Energy detection mode
Size: 1 Byte, Default Value: 0

Setting Description
0 0 = Report Power, Energy absolute value.
1 1 = Report positive / negative power, report the algebraic sum energy.
2 2 = Report positive / negative power, only report energy positive part (consuming electricity).
3 3 = Report positive / negative power, only report energy negative part (generating electricity).

Parameter 3: selective reporting

Enable selective reporting only when power change reaches a certain threshold or percentage set in parameters 4-11 below. This is used to reduce the network traffic.
Size: 1 Byte, Default Value: 1

Setting Description
0 0 = disable
1 1 = Enable

Parameter 4: Wattage threshold change

Threshold change in wattage to induce an automatic report (Whole EM)
Size: 2 Byte, Default Value: 50

Setting Description
0 - 30000 Valid values 0-30000

Parameter 5: Clamp 1

Threshold change in wattage to induce an automatic report (Clamp 1)
Size: 2 Byte, Default Value: 50

Setting Description
0 - 30000 Valid values 0-30000

Parameter 6: Clamp 2

Threshold change in wattage to induce an automatic report (Clamp 2)
Size: 2 Byte, Default Value: 50

Setting Description
0 - 30000 Valid values 0-30000

Parameter 7: Clamp 3

Threshold change in wattage to induce an automatic report (Clamp 3)
Size: 2 Byte, Default Value: 50

Setting Description
0 - 30000 Valid values 0-30000

Parameter 8: Clamp 4

Threshold change in wattage to induce an automatic report (Clamp 4)
Size: 2 Byte, Default Value: 50

Setting Description
0 - 30000 Valid values 0-30000

Parameter 9: Wattage percentage change

Percentage change in wattage to induce an automatic report (wohle EM)
Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid values 0-100

Technical Data

Hardware Platform ZM5101
Device Type Sub Energy Meter
Network Operation Always On Slave
Firmware Version HW: 0 FW: 1.03
Z-Wave Version 6.71.01
Certification ID ZC10-18086207
Z-Wave Product Id 0x0140.0x0803.0x1003
Supported Meter Type Electric Energy
Color White
Firmware Updatable Updatable by Consumer by RF
Frequency XXfrequency
Maximum transmission power XXantenna
CEPT (Europe)Sub Energy Meter