Quickstart
This is a
secure
Notification Sensor for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
To add the product to the system, please follow the following steps. 1. Start the COQON App 2. Select "Device" then "Settings" and tap on "+" to add your Window Sensor 3. Select COQON 4. Follow the steps in the App
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
The COQON Window & Door Contact FKABZ002 is a battery powered wireless magnetic contact that gives you optimal control over your doors and windows.With this contact, you keep track of all windows and doors - even when you're on the move.The window contact offers maximum security in your home and ensures safe protection against unauthorized access.He controls windows, doors or gates for you and can also control devices or smart scenes.Increase your comfort:In connection with a light control, for example, when entering the house, the lighting in the hallway can be switched on automatically.Feel safer:In the event of unauthorized access, an alarm is automatically triggered. At the same time you receive on request a push message.Protection class: IP20Battery life: up to 5 yearsControl of operation: Red LEDScope of delivery: Transmitter module and magnetic bracket incl. Batteries and mounting setDimensions: Magnetic angle: 55 x 15 x 12 mm, Transmitter module: 55 x 40 x 12 mmVersion: BasicPower voltage: 1x CR3032 lithium batteriesOperating temperature range: -15C to 85C (+/- 2.5C)Color: white RAL 9016Radio protocol: Z-Wave Plus
| Reset to factory default |
Factory reset: 1. Remove battery 2. Hold the Tamper3. Insert Battery 4. Release Tamper within 5 sec. Note: Please use this procedure only when the primary controller is missing or inoperable! |
| Inclusion |
To add the product to the system, please follow the following steps. 1. Start the COQON App 2. Select "Device" then "Settings" and tap on "+" to add your Window Sensor 3. Select COQON 4. Follow the steps in the App |
| Exclusion |
To remove your device from the system, please start the exclusion process to exclude the device from the COQON App. The device will be reset. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
5 |
Z-Wave Plus Lifeline |
Technical Data
| Hardware Platform |
ZM5101 |
| Device Type |
Notification Sensor |
| Network Operation |
Reporting Sleeping Slave |
| Firmware Version |
HW: 0 FW: 1.01 |
| Z-Wave Version |
6.71.01 |
| Certification ID |
ZC10-18086206 |
| Z-Wave Product Id |
0x0140.0x0801.0x1001 |
| Sensors |
Open/Closed (Binary) |
| Outdoor Use |
ok |
| Supported Notification Types |
Access ControlHome Security |
| Firmware Updatable |
Updatable by Consumer by RF |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
