Quickstart

This is a secure Notification Sensor for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
To start the motion detector's inclusion or exclusion mode,press the button three times in rapid succession. During inclusion and following configuration process the device is blinking.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Smart home from the socket.One product, four features, many possibilities: The MotionSwitch LED Z-Wave is a motion detector, brightness sensor, pushbutton and orientation light in one. No cable laying, no battery change - just plug it into the socket and off you go. The smart sensor can be quickly and easily integrated into Z-Wave based Smart Home systems like Smart Friends, making our everyday life smarter. For example, through automatic corridor lighting as soon as the 180infrared sensor with a range of 20 m detects movement. Or by automatically darkening as soon as a certain degree of brightness is reached. Thanks to the integrated button, actuators, for example a radio, can be switched on manually. And the automatic orientation light ensures good visibility at night with 3000 K. Smart Home can be so easy!

Reset to factory default	Please only perform these steps if the main network controller is missing or not working for other reasons.1 To set the sensor to "Reset", press the button three times in rapidsuccession and then press it once for several seconds.2 The device is now no longer included in the Z-Wave system and has been returned to factory settings
Inclusion	To start the motion detector's inclusion or exclusion mode,press the button three times in rapid succession. During inclusion and following configuration process the device is blinking.
Exclusion	To start the motion detector's inclusion or exclusion mode,press the button three times in rapid succession.During exclusion the device is blinking.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	1	Z-Wave Plus Lifeline- Device Reset Locally- Notifications:0x07 ( Home security )Motion Begin event ( 0x08 )0x07 ( Home security )Motion End event ( 0x00, 0x08 )- Binary Switch ReportLED state- Multilevel Sensor Reportvalue of internal ambient light sensor- Central scene notificationbutton events
2	16	On/Off control-Basic Set
3	16	Movement detection- Notifications:0x07 ( Home security )Motion Begin event ( 0x08 )0x07 ( Home security )Motion End event ( 0x00, 0x08 )
4	16	Ambient light- Multilevel Sensor Reportvalue of internal ambient light sensor
5	16	Button on/off-Basic Set
6	16	Button scene-Scene Activation Set
7	16	Button dim-Switch Multilevel Start Level Change-Switch Multilevel Stop Level Change

Configuration Parameters

Parameter 1: Time

Duration of light after motion detection.
Size: 2 Byte, Default Value: 180

Setting Description
5 - 900 seconds

Setting	Description
5 - 900	seconds

Parameter 10: Off behaviour

Behaviour after BASIC OFF (and similar commands).If a transition (even with zero change) with a non-default duration is to be processed, the transition cannot beinterrupted by any motion event in any case
Size: 2 Byte, Default Value: 10

Setting Description
0 LED is switched off and remains so until any new motion event (local or remote) is received.

1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution

255 LED is switched off for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Setting	Description
0	LED is switched off and remains so until any new motion event (local or remote) is received.
1 - 209	LED is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution
255	LED is switched off for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 11: On behaviour

Behaviour after BASIC ON (and similar commands).If a transition (even with zero change) with a non-default duration is to be processed, the transition cannot beinterrupted by any motion event in any case.
Size: 2 Byte, Default Value: 255

Setting Description
0 LED is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.

1 - 209 LED is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received. It then works normally via current motion evaluation. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.

255 LED is switched on for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Setting	Description
0	LED is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.
1 - 209	LED is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received. It then works normally via current motion evaluation. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.
255	LED is switched on for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 12: On behaviour time over

Time limit to stop waiting for motion after timeout of ON_BEHAVIOUR or OFF_ON_BEHAVIOUR (0-209) toprevent staying ON forever when there is no motion.
Size: 2 Byte, Default Value: 204

Setting Description
0 No additional waiting for motion.

1 - 209 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution

255 Never stop waiting for motion.

Setting	Description
0	No additional waiting for motion.
1 - 209	1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution
255	Never stop waiting for motion.

Parameter 13: Sequence On-Off behaviour

Behaviour after a rapid sequence of BASIC ON and BASIC OFF commands.The intention is to use a much longer timeout value than the time after a single ON command which should thenbe followed by a short timeout value.
Size: 2 Byte, Default Value: 204

Setting Description
0 LED is switched off and remains so until any new motion event (local or remote) is received.

1 - 209 LED is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution

255 device ignores ON - OFF sequence and uses OFF behaviour

Setting	Description
0	LED is switched off and remains so until any new motion event (local or remote) is received.
1 - 209	LED is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution
255	device ignores ON - OFF sequence and uses OFF behaviour

Parameter 14: Sequence Off-On behaviour

Behaviour after a rapid sequence of BASIC OFF and BASIC ON commands.The intention is to use a much longer timeout value than the time after a single OFF command which shouldthen be followed by a short timeout value.
Size: 2 Byte, Default Value: 204

Setting Description
0 LED is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.

1 - 209 LED is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received. It then works normally via current motion evaluation. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.

255 device ignores OFF - ON sequence and uses ON behaviour.

Setting	Description
0	LED is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.
1 - 209	LED is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received. It then works normally via current motion evaluation. Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.
255	device ignores OFF - ON sequence and uses ON behaviour.

Parameter 15: Sequence timing

Time in [100 milliseconds] of maximum delay between BASIC ON and BASIC OFF (and vice versa) to consider thisas a sequence. It is typically 1 second, but can be exceptionally longer due to retransmissions and overloadinthis case, a longer interval can be allowed (up to 5 seconds).
Size: 1 Byte, Default Value: 10

Setting Description
10 - 50 100 ms

Setting	Description
10 - 50	100 ms

Parameter 16: Motion Off behaviour

Motion disable timeout after BASIC SET to motion endpoint when the internal motion sensor is not used forevaluating the behaviour of the LED and groups 2 and 3. Events are, however, still transmitted to the Lifeline,and the device can be controlled via remote motion sensors.
Size: 2 Byte, Default Value: 0

Setting Description
0 BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still enabled

1 - 209 Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to Motion sensor endpoint. BASIC to root is mapped to Motion sensor endpoint.(SPIR) Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution

255 BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still disabled

Setting	Description
0	BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still enabled
1 - 209	Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to Motion sensor endpoint. BASIC to root is mapped to Motion sensor endpoint.(SPIR) Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution
255	BASIC SET to Motion sensor endpoint ignored, BASIC to root is mapped to LED endpoint, motion sensor still disabled

Parameter 17: Button behaviour

Bitfield descibing button functionability:Dim increase (bit 0):- long press of button does dim decreasing (0 = default)- long press of button does dim increasing (1)Scene switch (bit 1):- short press of button does toggleon/off (0 = default)- short press of button does scene switch (1)Standalone behaviour (bit 2):- using legacy sensor deactivity after button press (0 = default)- using cfg 10-14 sensor deactivity after button press (1)Network behaviour (bit 3):- using legacy sensor deactivity after button press (0)- using cfg 10-14 sensor deactivity after button press (1 = default)Dim disable (bit 4):- dim events (long press) are used (0 = default)- dim events (long press) are ignored (1)legacy sensor deactivity behaviour does this:-Pressing push button when LED is OFF: LED will switch on as long as there is movement and the delay time runsof-Pressing push button when LED is ON: LED will switch off as long as there is movement ans the delay time runsof (invers logic).cfg 10-14 sensor deactivity behaviour uses behaviour specified in parameters 10-14 (the same behaviour aspressing of external switch using BASIC ON/OFF functions)
Size: 1 Byte, Default Value: 8

Setting Description
0 - 31 bit field

Setting	Description
0 - 31	bit field

Parameter 18: Button scenes

Parameters 18 specifies scene numbers (from 1 to number) to be switched by toggle button.
Size: 1 Byte, Default Value: 1

Setting Description
0 do not use any scene

1 - 127 up to scene number

Setting	Description
0	do not use any scene
1 - 127	up to scene number

Parameter 19: Legacy inactivity time

In legacy button mode function this timeout is used to cancel motion sensor inactivity mode after motion end(both for on and off state of LED).
Size: 2 Byte, Default Value: 103

Setting Description
1 - 209 Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution

Setting	Description
1 - 209	Timeout: 1..1001 second (1) to 100 seconds (100) in 1-second resolution 101..2001 minute (101) to 100 minutes (200) in 1-minute resolution 201..2091 hour (201) to 9 hours (209) in 1-hour resolution

Parameter 2: Light

Lux threshold for night mode detection
Size: 2 Byte, Default Value: 2000

Setting Description
0 run Learn ambient light sequence

2 - 1999 Lux

2000 is used as daylight (always night mode)

Setting	Description
0	run Learn ambient light sequence
2 - 1999	Lux
2000	is used as daylight (always night mode)

Parameter 5: Sensitivity

PIR sensitivity
Size: 1 Byte, Default Value: 100

Setting Description
2 - 100 %

Setting	Description
2 - 100	%

Parameter 6: Brightness measuring interval

Interval for measuring ambient light when lamp is on (lamp switches off briefly and measures).
Size: 1 Byte, Default Value: 0

Setting Description
0 function is off

5 - 120 minuts

Setting	Description
0	function is off
5 - 120	minuts

Parameter 8: Global light

When GLOBAL_LIGHT mode is ONdevice overrides its own light sensor values and uses Light report valuesfrom any Z-Wave light sensor insteadthis has to be configured appropriately to send light automatically.If the last remote light level value is older than 30 minutes, the internal light value is used again until the nextexternal value is received.
Size: 1 Byte, Default Value: 1

Setting Description
0 - 1 binary off/on

Setting	Description
0 - 1	binary off/on

Parameter 9: Slave mode

Slave mode (bit0) means:LED is directly controlled via Z-Wave, internal sensors are not used for controlling itCentral unit checking (bit 1): (useful especially for controlling via gateway)When slave bit is 0:- device signalises fail of lifeline connection (if this bit is zero, fail of lifeline connection is not signalised)When slave bit is 1:- device checks presence of Z-Wave device in lifeline group (gateway). If it is not present for 2 minutes (testingrepeatedly every 30 seconds) device switches to normal mode in the same way as after the end of local disabledmode (ON_BEHAVIOUR)- the device checks every 1 minute for recovery of Lifeline connection.- if no lifeline specified - it works in normal mode
Size: 1 Byte, Default Value: 2

Setting Description
0 Normal mode

1 Slave mode

2 Normal mode with checking lifeline

3 Slave mode with checking lifeline

4 LED is permanently on

Setting	Description
0	Normal mode
1	Slave mode
2	Normal mode with checking lifeline
3	Slave mode with checking lifeline
4	LED is permanently on

Technical Data

Hardware Platform	ZM5202
Device Type	Notification Sensor
Network Operation	Always On Slave
Firmware Version	HW: 1 FW: 1.132:02.35
Z-Wave Version	6.71.03
Certification ID	ZC10-18076193
Z-Wave Product Id	0x0271.0x0002.0x19FB
Z-Wave Scene Type	Central Scene
Firmware Updatable	Updatable by Consumer by RF
Sensors	LuminanceMotion/No Motion (Binary)
Color	White
Supported Notification Types	Emergency Alarm
Switch Type	Push Button
Frequency	XXfrequency
Maximum transmission power	XXantenna

Steinel GmbH

Motion Switch LED

SKU: 40111665101