Quickstart
This is a
secure
Notification Sensor for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
1,Power up the device. 2, Set Z-Wave Controller into inclusion mode 3, Press the button 3 times within 1s to enter inclusion mode. 4,The device will be recognized and automatically included into Z-Wave Network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
In the Z-Wave network communications, water sensor can work with any Z-Wave main controller. In the Z-Wave network communications, water sensor can send messages to the Z-Wave main controller, and realize association with other devices through the Z-Wave network. In the communication with the Z-Wave main controller, thewater sensor cansendmessages to the Z-Wave main controller, but it can notreceivemessages from the Z-Wave main controller. When the water sensor is triggered, the LED light keeps on and the buzzer will make sound. The water sensor sends messages to the Z-Wave main controller at the same time, the Z-Wave main controller will display the current status of water sensor. Water sensor is battery powered, is small and can be installed easily.
| Reset to factory default |
1,Power up the device.2, Press and hold the button for 10s until led light is on, then release the button.Please use this procedure only when the network primary controller is missing or otherwise inoperable |
| Inclusion |
1,Power up the device. 2, Set Z-Wave Controller into inclusion mode 3, Press the button 3 times within 1s to enter inclusion mode. 4,The device will be recognized and automatically included into Z-Wave Network. |
| Exclusion |
1, Power up the device. 2,Set Z-Wave Controller into exclusion mode 3, Press the button 3 times within 1s to enter exclusion mode |
| NIF |
XXXNIF |
| Wakeup |
Press the button briefly,Led will blink once. |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
5 |
Group 1 is lifeline group; all nodes which associated in this group will receive the messages sent bydevice through lifeline. Command Class:COMMAND_CLASS_NOTIFICATIONCOMMAND_CLASS_SENSOR_BINARYCOMMAND_CLASS_BATTERYCOMMAND_CLASS_DEVICE_RESET_LOCALLYEvent:NOTIFICATION_REPORTSENSOR_BINARY_REPORTBATTERY_REPORTDEVICE_RESET_LOCALLY_NOTIFICATION |
| 2 |
5 |
Group 2 is controlling group, all nodes associated in this group will be controlled through BASIC_SETcommand by the device when device detects a water leakage event. Command Class:COMMAND_CLASS_BASICEvent:BASIC_SET |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Notification Sensor |
| Network Operation |
Reporting Sleeping Slave |
| Firmware Version |
HW: 32 FW: 2.133 |
| Z-Wave Version |
6.81.00 |
| Certification ID |
ZC10-18076181 |
| Z-Wave Product Id |
0x0258.0x0200.0x1025 |
| Supported Notification Types |
Water AlarmWater Valve |
| Controller Supports Multiple Networks |
ok |
| Controller Supports Multiple Z-Wave Interfaces |
ok |
| Gateway Has Preferred Partners |
ok |
| Firmware Updatable |
Updatable by Manufacturer Representative |
| Sensors |
Water Flow |
| Color |
White |
| Communications Connections |
None |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
