Quickstart
This is a
Notification Sensor for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
Inclusion: Including the REM50Z into an Existing Network:1. Set your primary controller to Include mode, to add the REM50Z as a node on your network(see your controllers user manual for detailed instructions).2. Press the Install button. The controller will indicate the device has been included into the network.Your controller will indicate the REM50Z was successfully added to its network (see your controllers user manual for details). Inclusion and exclusion are always done at normal transmit power mode.If your controller supports NWI, then you can optionally set the primary to NWI include mode. Please note that NWI inclusion mode does not end when you have included a new node. This allows multiple nodes to be included without having to physically go back to the controller to initiate the next inclusion. Therefore you must manually terminate NWI inclusion mode at the controller when you have finished including any new nodes to the network. Since intermediate included nodes will assist the inclusion process by routing messages, we recommend that nodes close to the primary controller be installed first, proceeding out in consecutive rings from the controller.Note: Consult your controllers user manual for details on removing a device from a Z-Wave network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
The REM50Z (Remote Equipment Monitor) Quad Channel Remote Temperature Sensor is a wall mountable Z-Wave remote temperature sensor for use with all Z-Wave systems.This sensor is ideal for remotely monitoring up to 4 operating temperatures on HVAC systems: Supply, Return, and Refrigeration In/Out Line Temps.Additionally, the REM50 has a single channel contact closure / voltage detection circuit that can be used to monitor and report Condensate Pan fill level of the HVAC system.Features Z-Wave 500 Series RadioSupports Z-Wave PlusQuad Temp Sensor Circuits:+/- 1 degree F, Range:-40F to 120FoDesigned for 10k Thermistor temp sensors, not included1 Contact Closure / Voltage Detection CircuitoDesigned to detect Float Switch closure, not included6 Status LEDsDesigned for interior use in mechanical room, attic or crawlspaceCompatible with RCS Z-Wave ThermostatsCompatible with all Z-Wave systemsWall MountableSmall, Thin, LightweightGrey, PaintableDimensions5.10 X 2.25 X 0.9Power1628 VAC1224 VDC
| Reset to factory default |
Factory ResetNOTE: A Factory Reset should only be performed if the network controller is missing or inoperable.To reset the REM50Zs configurations and Z-Wave parameters to Factory Settings (Including association groups and scene configurations), and remove the REM50Z from any Z-Wave network:1. Hold down the Install button for approximately 10 seconds2. Release the install button (the REM50Z will reset all internal configuration including Z-Wave configurations). The unit will then reset.3. When the Status LED begins to blink (un-enrolled) the unit has finished restoring configurations is running in normal mode.A Restore Defaults will be performed automatically when removed from a network. |
| Inclusion |
Inclusion: Including the REM50Z into an Existing Network:1. Set your primary controller to Include mode, to add the REM50Z as a node on your network(see your controllers user manual for detailed instructions).2. Press the Install button. The controller will indicate the device has been included into the network.Your controller will indicate the REM50Z was successfully added to its network (see your controllers user manual for details). Inclusion and exclusion are always done at normal transmit power mode.If your controller supports NWI, then you can optionally set the primary to NWI include mode. Please note that NWI inclusion mode does not end when you have included a new node. This allows multiple nodes to be included without having to physically go back to the controller to initiate the next inclusion. Therefore you must manually terminate NWI inclusion mode at the controller when you have finished including any new nodes to the network. Since intermediate included nodes will assist the inclusion process by routing messages, we recommend that nodes close to the primary controller be installed first, proceeding out in consecutive rings from the controller.Note: Consult your controllers user manual for details on removing a device from a Z-Wave network. |
| Exclusion |
Exclusion: Removing the REM50Z from a Network:1. Set your primary controller to Remove mode, to remove the REM50Z as a node on your network (see your controllers user manual for detailed instructions).2. Press the Install button. The controller will indicate the device has been removed from the network. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
1 |
Z-Wave Plus Lifeline -Device Reset LocallySupply Air Sensor (Multilevel Sensor Report and Multilevel Sensor Report, Multichannel)Return Air Sensor (Multilevel Sensor Report, Multichannel)Coil Low Sensor (Multilevel Sensor Report, Multichannel)Coil High Sensor (Multilevel Sensor Report, Multichannel)Float Sensor(Notification Report) |
| 2 |
2 |
Supply Air Sensor (Multilevel Sensor Report, Multichannel) |
| 3 |
2 |
Return Air Sensor (Multilevel Sensor Report, Multichannel) |
| 4 |
2 |
Temp - S3 Sensor (Multilevel Sensor Report, Multichannel) |
| 5 |
2 |
Temp - S4 Sensor (Multilevel Sensor Report, Multichannel) |
| 6 |
2 |
Float SW(Notification Report) |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Notification Sensor |
| Network Operation |
Always On Slave |
| Firmware Version |
HW: 1 FW: 6.61:01.00 |
| Z-Wave Version |
6.61.00 |
| Certification ID |
ZC10-18076173 |
| Z-Wave Product Id |
0x0010.0x454D.0x3530 |
| Color |
Gray |
| Sensors |
Air TemperatureVoltage |
| Firmware Updatable |
Updatable by Consumer by RF |
| Supported Notification Types |
Water Alarm |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
