This is a
Pairs the multi-channel remote with an existing shade network as an additional remote.On the remote, press and hold theMENU/RIGHT button to enter the menu.3. Select ZWAVE > LEARN.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Enjoy the comfort, convenience and energy efficiency of beautiful custom motorized window treatments featuring Z-Wave protocol for easy integration. Lighting control has never been more simple. Window treatments can be automated using your favorite Z-Wave certified gateway or security system, or controlled by a remote control. Raise or lower the shades to control just the right amount of light, privacy and solar heat. Shades can be fully open, fully closed or anywhere in between, its up to you. In addition, some systems will also report back the state of the battery charge on battery operated versions.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Restores the remote back to a factorystate by removing all memory of shadeand remote pairings from the remote.1. On the remote, press and hold theMENU/RIGHT button to enter the menu.2. Select ZWAVE > RESET.3. With LIKE NEW? selected, press andhold the MENU/RIGHT button until thescreen no longer tells you to wait.Please use this procedure only when the network primary controller is missing or otherwise inoperable.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.
This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device. To wakeup the device please perform the following action: Any button press will wake up the remote.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline (Primary)Battery Status CCDevice Reset Locally CCCentral Scene CC |
2 | 12 | Slave Shade Group (12 Nodes Max)CC MultiLevel Switch |
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
Adding your shades and remotes to the same shade network (a group of shades and remotes that communicate with eachother) or to a home automation system.1. Press and hold the MENU/RIGHT buttonfor 2 seconds to enter the menu.2. Select ZWAVE > INCLUDE.3. On the shade you want to pair,press and hold the program button for3 seconds. When the shade LED flashesgreen, release the button.The remotes screen will indicate
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
Removing the current pairing between your shades and remotes.1. On the remote, press and hold the MENU/RIGHT buttonfor 2 seconds to enter the menu.2. Select ZWAVE > EXCLUDE.3. On the shade, press and hold the program button for3 seconds. When the shade LED flashes green, releasethe button.The remotes screen will indicate that the shade has been removed fromthe remote. The shade will jog.
Hardware Platform | ZM5101 |
Device Type | Remote Control - Simple |
Network Operation | Portable Controller |
Firmware Version | HW: 255 FW: 11.14 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-18066153 |
Z-Wave Product Id | 0x026e.0x4D43.0x5A31 |
Color | White |
Firmware Updatable | Not Updatable |
Switch Type | Push Button with Indicator |
Window Covering Control Features | Endpoint Aware |
Z-Wave Scene Type | Central Scene |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |