Everspring
MOTION DETECTOR
SKU: SP817-1
Quickstart
This is a
1. Put the Z-Wave Controller into inclusion mode.2. Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This presence detector using PIR (passive infrared receiver) detects the presence of a person in a room. The units compatible with S2 security, send information to a controller or any other associated Z-Wave device. Up to 4 devices can be controlled from this device. The sensor is a battery-powered device, which is in sleeping mode unless an action is detected. After a programmable sleeping time the device wakes up and sends a status information. After this the unit goes back to sleeping mode. Batteries can be changed without unscrewing the device from the door or frame. The unit will give a visual warning on the device and sends a warning to the Z-Wave controller, when batteries need to be replaced. The unit offers a tampering control and sends an alarm message when tampered.
| Reset to factory default | Please use this procedure only when the network primary controller is missing or otherwise inoperable.1. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.2. Within 1 second of step 1, press the tamper switch again and hold until LED is off (about 5 seconds).3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes. |
| Inclusion | 1. Put the Z-Wave Controller into inclusion mode.2. Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode. |
| Exclusion | 1. Put the Z-Wave Controller into exclusion mode.2. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode. |
| NIF | XXXNIF |
| Wakeup | After it has been included into a Z-Wave network, the detector will go to sleep but will send a Wakeup Notification Command periodically at preset period to the controller. The Motion detector will stay awake for 10 seconds at least and then go back to sleep to conserve battery life.The time interval between Wakeup Notification Commands can be set in the Wakeup Command Class based on the range values below:1) Minimum Wake Up Interval 600s (10 minutes)2) Maximum Wake Up Interval 86400s (1 day)3) Default Wake Up Interval 14400s (4 hours)4) Wake Up Interval Step Seconds 600s (10 minutes) |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
| 2 | 4 | PIR Control |
Configuration Parameters
Parameter 1: Basic Set Level
When Basic Set Command is sent where contains a value, the receiver will take it for consideration; for instance, if a lamp module is received the Basic Set command of which value is decisive as to how bright of dim level of lamp module shall be. Size: 1 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 1 - 99 | Basic Set Level |
Parameter 3: Sensitivity Level
In order to provide a best efficiency of the detector, it is recommended to test the detector with movements from a farthest end of the coverage area at first time of use.If movements cannot be detected sensitively, simply adjust the sensitivity level with Configuration Parameter #3. This parameter can be configured with the value of 1 through 10, where 1 means low sensitivity and 10 means highest sensitivity. Size: 1 Byte, Default Value: 6
| Setting | Description |
|---|---|
| 1 - 10 | Sensitivity Level |
Parameter 4: Re-trigger Interval
The Configuration parameter that can be used to adjust the interval of being re-triggered after the detector has been triggered as Configuration Parameter #4.No response will be made during this interval if a movement is presented.The time interval can be set between 5 secs to 3600 secs. Size: 2 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 5 - 3600 | Re-trigger Interval |
Parameter 5: Lux Level
The user can set a detecting percentage of lux level which determines when the light sensor will be activated.If percentage of lux level of ambient illumination falls below this percentage, and a person moves across or within the protected area, the detector will emit Z-Wave ON Command (i.e. Basic Set Command (Value = Basic Set Level)) to controller and activate connected modules and lighting.Percentage can be set between 1% to 100%. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 1 - 100 | Lux Level |
Parameter 6: On-Off Duration
The function of on-off duration setting will be useful if the detector is connected with a module or lighting.The duration determines how long the module/lighting should stay ON.For instance, Lamp Module turns off 100 secs after it has been turned on.This parameter can be configured with the value of 5 through 3600, where 5 means 5 second delay and 3600 means 3600 seconds of delay. Size: 2 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 5 - 3600 | On-Off Duration |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.00:00.05 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18066147 |
| Z-Wave Product Id | 0x0060.0x0001.0x0006 |
| Color | White |
| Supported Notification Types | Home Security |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |