Aibase

4-in-1 Motion Sensor

SKU: HA-ZW-5SABC

ZWave+ Security V2

Quickstart

This is a secure Notification Sensor for XXXQFrequencyName. To run this device please make sure the internal battery is fully charged. To add this device to your network execute the following action:
Add 4-in-1 Motion Sensorinto a Z-Wave network: a. Let the primary controller go into inclusion mode (If you dont know how to do this, refer to its manual).b. Short Press one time this Z-Button.c. The 4-in-1 Motion Sensor LED will blink, If the inclusion is successful, then LED will keep on 2 seconds. Otherwise, the LED will blink until timeout, in which case you need to repeat the process from step b.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

The 4-in-1 motion sensor is designed for using with scenes in home automation systems, integrate motion, light, temperature and humidity sensors, powered by CR123A battery or MicroUSB cable. The Motion Sensor lets you know when movement is detected in a certain area and can trigger different actions in response to that movement (or lack of movement). It also lets you know the ambient temperature and humidity to trigger different actions to make you more comfort. This sensor integrated Z-Wave communication module to connect with Z-Wave gateway, and this device can be adapted to EU(868.42Mhz) or US(908.42MHz).
Reset to factory default Reset 4-in-1 Motion Sensorto factory Default:1. Press and hold the Z-Button for 5 seconds.2. If holding time is more than 5 seconds, the LED will blink fast at acceleration. If reset success 4-in-1 Motion Sensor LED will turn off. When the Z-Button is released, it will send Device Reset Locally Command. Otherwise please repeat step 2.Note:1, This procedure should only be used when the primary controller is inoperable.2, Reset 4-in-1 Motion Sensor to factory default settings.It will set the 4-in-1 Motion Sensor to not in Z-Wave network state; delete the Association setting and restore the Configuration setting to the default.
Inclusion Add 4-in-1 Motion Sensorinto a Z-Wave network: a. Let the primary controller go into inclusion mode (If you dont know how to do this, refer to its manual).b. Short Press one time this Z-Button.c. The 4-in-1 Motion Sensor LED will blink, If the inclusion is successful, then LED will keep on 2 seconds. Otherwise, the LED will blink until timeout, in which case you need to repeat the process from step b.
Exclusion Remove 4-in-1 Motion Sensorfrom a Z-Wave network: a. Let the primary controller go into exclusion mode (If you dont know how to do this, refer to its manual).b. Short Press one time this Z-Button.c. The 4-in-1 Motion Sensor LED will keep on, If the remove is successful, then LED will blink 2 seconds. Otherwise, the LED will keep on until timeout, in which case you need to repeat the process from step b.Note: 4-in-1 Motion Sensor will go away Z-Wave SmartStart Inclusion when it is removed from a Z-Wave network.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Z-Wave Plus Lifeline1. Notification Report.Sensor will send Notification Report when Motion Detection Unknown Location and (Event inactive).2. Multilevel Sensor ReportSensor will send Multilevel Sensor Report (Temperature, humidity, luminance) interval of 2 hours.3. Battery Report.Sensor will send Battery Report when the battery level is low and the battery reports value is 0xFF.4. Device Reset Locally.
2 5 Send Basic Set when PIR trigger

Configuration Parameters

Parameter 10: Low Battery Power Level

Low Battery Power Level of alarm threshold values: the value range are 10~50 for percentage, so the Battery Low Power level can setting 10%~50%.
Size: 1 Byte, Default Value: 10

Setting Description
10 - 50 Low Battery Power Level of alarm threshold values

Parameter 100: Set 101 ~ 104 to default.

Set 101 ~ 104 to default.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 Set 101 ~ 104 to default.

Parameter 101: The interval time of sending the temperature reporting

The interval time of sending the temperature reporting. if setting to 0 then the temperature reporting is disabled 1. Valid values: 0x00-0x28DE802. The minimum interval time is 1 minutes. For example, if the value is set to be more than 1 and less than 60, the interval time is 1 minutes, if the value is set to be more than 60 and less than 120, the interval time is 2 minutes.
Size: 4 Byte, Default Value: 7200

Setting Description
0 the temperature reporting is disabled
1 - 2678400 The interval time of sending the temperature reporting is 31 days2678400 seconds

Parameter 102: The interval time of sending the humidity reporting.

The interval time of sending the humidity reporting. if setting to 0 then the humidity reporting is disabled 1. Valid values: 0x00-0x28DE802. The minimum interval time is 1 minutes. For example, if the value is set to be more than 1 and less than 60, the interval time is 1 minutes, if the value is set to be more than 60 and less than 120, the interval time is 2 minutes.
Size: 4 Byte, Default Value: 7200

Setting Description
0 the luminance reporting is disabled
1 - 2678400 The interval time of sending the humidity reporting is 31 days2678400 seconds

Parameter 103: The interval time of sending the luminance reporting.

The interval time of sending the luminance reporting. if setting to 0 then the luminance reporting is disabled 1. Valid values: 0x00-0x28DE802. The minimum interval time is 1 minutes. For example, if the value is set to be more than 1 and less than 60, the interval time is 1 minutes, if the value is set to be more than 60 and less than 120, the interval time is 2 minutes.
Size: 4 Byte, Default Value: 7200

Setting Description
0 the luminance reporting is disabled
1 - 2678400 The interval time of sending the luminance reporting is 31 days2678400 seconds

Parameter 104: The interval time of sending the battery level reporting.

The interval time of sending the battery level reporting. if setting to 0 then the battery level reporting is disabled 1. Valid values: 0x00-0x28DE802. The minimum interval time is 1 minutes. For example, if the value is set to be more than 1 and less than 60, the interval time is 1 minutes, if the value is set to be more than 60 and less than 120, the interval time is 2 minutes.
Size: 4 Byte, Default Value: 86400

Setting Description
0 the battery level reporting is disabled
1 - 2678400 The interval time of sending the battery level reporting is 31 days2678400 seconds

Parameter 110: Enable 111 ~ 114 temperature/humidity/luminance/ battery level change reporting.

Enable 111 ~ 114 temperature/humidity/luminance/ battery level change reporting.0 = Unable1 = Enable
Size: 1 Byte, Default Value: 0

Setting Description
0 Unable
1 Enable

Parameter 111: Configuration temperature change threshold.

Configuration temperature change threshold.Valid values: 1-500(unit 0.1)
Size: 2 Byte, Default Value: 10

Setting Description
1 - 500 the temperature change threshold value(unit 0.1)

Parameter 112: Configuration humidity change threshold.

Configuration humidity change threshold.Valid values: 1-32(unit %)
Size: 1 Byte, Default Value: 5

Setting Description
1 - 32 humidity change threshold value(unit %)

Parameter 113: Configuration luminance change threshold.

Configuration luminance change threshold.Valid values: 1-65528(unit lx)
Size: 2 Byte, Default Value: 150

Setting Description
-32767 - -1 luminance change threshold is 32767 to 65528
0 - 32766 luminance change threshold is 0 to 32766

Parameter 114: Configuration battery level change threshold.

Configuration battery level change threshold.Valid values: 1-100(unit %)
Size: 1 Byte, Default Value: 10

Setting Description
1 - 100 battery level change threshold value(unit)%

Parameter 12: Turn on/off PIR

Turn on/off PIR 0x0A indicates the highest sensitivity, 0x00 means off PIR detection function.
Size: 1 Byte, Default Value: 10

Setting Description
0 - 10 0x0A indicates the highest sensitivity, 0x00 means off PIR detection function.

Parameter 13: PIR triggers the waiting time value

PIR triggers the waiting time value
Size: 2 Byte, Default Value: 30

Setting Description
0 Unable
1 Enable

Parameter 14: Whether the BASIC SET command is sent after the PIR is triggered

Whether the BASIC SET command is sent after the PIR is triggered
Size: 1 Byte, Default Value: 0

Setting Description
0 Unable
1 Enable

Parameter 15: PIR triggers the correspondence between the value of the Basic set and the PIR state

PIR triggers the correspondence between the value of the Basic set and the PIR state, When value is 0x00 PIR triggers Send the basic set command 0xff PIR alarm release send the basic set command 0x00, otherwise PIR triggers send the basic set command 0x00 PIR alarm release send the basic set command 0xff.
Size: 1 Byte, Default Value: 0

Setting Description
0 PIR triggers Send the basic set command 0xff PIR alarm release send the basic set command 0x00
1 PIR triggers send the basic set command 0x00 PIR alarm release send the basic set command 0xff.

Technical Data

Hardware Platform ZM5101
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Firmware Version HW: 3 FW: 0.10
Z-Wave Version 6.81.00
Certification ID ZC10-18066141
Z-Wave Product Id 0x0384.0x0200.0x0009
Supported Notification Types Access ControlLuminance
Sensors Air Temperature
Firmware Updatable Not Updatable
Frequency XXfrequency
Maximum transmission power XXantenna
U.S. / Canada / MexicoNotification Sensor