Aeotec
Nano Shutter
SKU: ZW141-B
Quickstart
This is a
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeotec Nano Shutter is a Z-Wave motor controller specifically used to enable Z-Wave command and control (up/down/stop) for existing window covering motors.It can connect to 2 external manual switches/buttons to control the motor up/down/stop independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Nano Shutter.The wireless module is powered from the mains supply. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.Nano Shutter is also a security Z-Wave plus device and supports Over The Air (OTA) feature for the products firmware upgrade.It can be a repeater in the Z-Wave network. Acting as a bridge for communication, it will forward Z-Wave command messages to their destinations if the originating controller is out of range from the destination node. By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary listening Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices.
| Reset to factory default | Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. |
| Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing. |
| Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, quick press the products Action button 6 times that you can find on the product's housing. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline.When the load state of Nano Shutter (turn on/off the load) is changed, the Basic Report (configured by parameter 80) can be sent to the associated nodes in this group. |
| 2 | 5 | Forward the Basic Set, Binary Switch Set, Scene Activation Set to associated nodes in Group 2 when the Nano Shutter receives the Basic Set, Binary Switch Set, Scene Activation Set commands from main controller. (E.g. Send/forward Basic Set to control the other nodes in association Group 2) |
Configuration Parameters
Parameter 120: Configure the external switch mode for S1.
Configure the external switch mode for S1. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unidentified mode |
| 1 | Reserved |
| 2 | 3 way switch mode |
| 3 | Momentary push button mode |
| 4 | Enter automatic identification mode |
Parameter 121: Configure the external switch mode for S2.
Configure the external switch mode for S2. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unidentified mode |
| 1 | Reserved |
| 2 | 3 way switch mode |
| 3 | Momentary push button mode |
| 4 | Enter automatic identification mode |
Parameter 252: Lock/unlock configuration parameters
Lock/unlock configuration parameters. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unlock |
| 1 | Lock |
Parameter 255: Reset the Nano Shutter
Reset the Nano Shutter to factory default. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Reset all configuration parameters to factory default setting |
| 1431655765 | Reset to factory default setting and removed from the z-wave network |
Parameter 35: Set the moving time from up (left) to down (right) forcurtain.
Set the moving time from up (left) to down (right) for curtain.Note: the time unit is second. Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 127 | The available range for time set is 1 to 127 seconds. |
Parameter 80: To set which notification would be sent to the associated devices (Group 1)
To set which notification would be sent to the associated devices (Group 1) when the state of Nano Shutter is changed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Send Nothing |
| 1 | Send Basic CC report |
Parameter 85: Set the operation mode of external switch
Set the operation mode of external switch.Note: for the description of Operation Mode 1 or 2, please refer to the user manual. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Operation Mode 1 |
| 1 | Operation Mode 2 |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Window Covering - No Position/Endpoint |
| Network Operation | Always On Slave |
| Firmware Version | HW: 141 FW: 1.00:01.00 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18066131 |
| Z-Wave Product Id | 0x0086.0x0203.0x008D |
| Firmware Updatable | Updatable by Consumer by RF |
| Window Covering Control Features | Endpoint Aware |
| Z-Wave Scene Type | Scene |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |