This is a
Add for inclusion: 1).Insert the battery.2).Set the Z-Wave network main controller into learning mode.3).Triggering this action button.4).If the add for inclusion is successful, the LED will blink fast and then keep on 3 seconds. Otherwise, the LED will blink 25 seconds and then turn off, in which case you need to repeat the process from step
Well design to match your door/window installation Firmware Wireless update Low voltage alarm to remind changing battery Easy installation by screws or 3M adhesive tape.
Reset to factory default | LED will blink fast for 5 seconds and then keep solid for 3 seconds, after that Door/Window Sensor will send Device_Reset_Locally to the main controller and exclude from the Z-Wave network.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion | Add for inclusion: 1).Insert the battery.2).Set the Z-Wave network main controller into learning mode.3).Triggering this action button.4).If the add for inclusion is successful, the LED will blink fast and then keep on 3 seconds. Otherwise, the LED will blink 25 seconds and then turn off, in which case you need to repeat the process from step |
Exclusion | Remove for exclusion;1.Insert the CR battery.2.Set the Z-Wave network main controller into exclusion mode.3.Triggering this action button.If the remove for exclusion is successful, the LED will blink fast and turn off. Otherwise, the LED will keep solid for 2 seconds and then turn off, in which case you need to repeat the process from step 2. |
NIF | XXXNIF |
Wakeup | 1. Short press 3 time.2. LED will blink one time; sending wake up notification cc |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | 1. Notification Report.Sensor will send Notification Report when the supported event is triggered.2. Battery Report.Sensor will send Battery Report when the battery level is low and the battery reports value is 0xFF.3. Device Reset Locally. |
2 | 5 | 1.Basic SetSensor will send Basic Set when the sensor body and magnet removed or combined. |
This parameter defines a battery level as the low battery. Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 - 50 | % |
Door/Window Sensor can send BASIC SET command to nodes associated with group 2 Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Door/Window Sensor can reverse its value of BASIC SET when the magnet is triggered. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send BASIC SET VALUE = 255 to nodes associated with group 2 when door/window is opened.Send BASIC SET VALUE = 0 to nodes associated with group 2 when door/window is closed. |
1 | Send BASIC SET VALUE = 0 to nodes associated with group 2 when door/window is opened.Send BASIC SET VALUE = 255 to nodes associated with group 2 when door/window is closed. |
Lock/unlock all configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Unlock |
1 | Lock |
Hardware Platform | ZM5101 |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 32 FW: 1.08 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-18056126 |
Z-Wave Product Id | 0x0384.0x0200.0x0008 |
Supported Notification Types | Access ControlHome Security |
Sensors | Open/Closed (Binary) |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |