Jasco
2 Button Hub/Panel Remote
SKU: 37792 / ZW5307
Quickstart
This is a
Adding your remote to a Z-Wave network1. Follow the instructions for your Z-Wave certified hub to add a device to the Z-Wave network.2. Once the hub is ready to add your device, press and hold Button 1 for 3 seconds.3. The LED will flash two (2) times when the remote sends add notification (NIF).NOTE: Some Hubs will require an additional step for secure inclusion, when prompted scan the QR code on the back of the remote, or type in the 5-digit pin code located on the back of the remote.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Custom lighting control is at your fingertips with the Jasco Z-Wave 2-Button Portable Hub Remote. This versatile remote communicates with your hub to activate up to 6 unique, lighting scenes. Once the remote is connected to your existing network, you can begin programming the lights to personalize your indoor space. The wireless lighting control has an overall signal range of up to 150 feet and is compatible with any device that works with your hub.Enjoy a variety of placement options for your lighting controlutilize the included hardware and magnetic bracket for wall mounting, detach the remote for instant portability or pair the remote with a separate stand for convenient tabletop use. The hub remote also functions on a scalable system, giving you the freedom to start with one remote and add as many as you need. Take control of your lights with the Z-Wave 2 Button Portable Hub Remote.
| Reset to factory default | Returning your remote to factory defaults1. Press and release Button 1 ten times quickly. All button presses must be within 6 seconds.2. The LED will flash five (5) times when completed successfully.NOTE: This should only be used in the event your network's primary controller/hub is missing or otherwise inoperable. |
| Inclusion | Adding your remote to a Z-Wave network1. Follow the instructions for your Z-Wave certified hub to add a device to the Z-Wave network.2. Once the hub is ready to add your device, press and hold Button 1 for 3 seconds.3. The LED will flash two (2) times when the remote sends add notification (NIF).NOTE: Some Hubs will require an additional step for secure inclusion, when prompted scan the QR code on the back of the remote, or type in the 5-digit pin code located on the back of the remote. |
| Exclusion | Removing your remote from a Z-Wave network1. Follow the instructions for your Z-Wave certified hub to remove a device from the Z-Wave network.2. Once the hub is ready to remove your device, press and hold Button 1 for 3 seconds.3. The LED will flash two (2) times when the remote sends remove notification (NIF). |
| NIF | XXXNIF |
| Wakeup | 1. Press and hold Button 1 for 3 seconds.2. The LED will flash two (2) times. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 2 | Association Group 1 supports Lifeline, Battery Reports, DeviceReset Locally Notification |
Configuration Parameters
Parameter 21: Adjust Refresh
Adjust Refresh Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 10 Seconds |
| 1 - 55 | Seconds |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Wall Controller |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 255 FW: 5.18 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18056118 |
| Z-Wave Product Id | 0x0063.0x4843.0x3133 |
| Color | White |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |