Aeotec
NanoMote One
SKU: ZWA004-A
Quickstart
This is a
Includeddevice:1. Insert the LIR2450 battery.2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual).3. Pressing and holding the button for 3 seconds.4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The NanoMote One is a wireless, portable and rechargeable scene switch. It can control a Z-Wave device, such as smart plug, smart dimmer with a Z-Wave gateway. You can also activate a scene like sleep scene, movie scene and entertainment scene with it.
| Reset to factory default | Pressing and holding the button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds.Using this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | Includeddevice:1. Insert the LIR2450 battery.2. Set the Z-Wave network main controller into learning mode( see Z-Wave network controller operating manual).3. Pressing and holding the button for 3 seconds.4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds. |
| Exclusion | To remove the NanoMote One from the Z-Wave network:(1) Insert the LIR2450 battery.(2) Set the Z-Wave network main controller into remove mode(see Z-Wave controller operating manual).(3) Triple click the button, if the exclusion is successful, LEDwill blink in orange for less than 5 seconds and then keep onfor 3 seconds. |
| NIF | XXXNIF |
| Wakeup | Pressing and holding Button for 3 seconds. Led will turn to green,which means Scene Controller has been woken up. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Scene Controller will send Scene Controller sends the central scene notification command and battery report command to the associated nodes. |
| 2 | 5 | Scene Controller will send Basic Set command to the associated nodes. |
| 3 | 5 | Scene Controller will sendswitch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes. |
Configuration Parameters
Parameter 32: Level of low battery
Define a battery level as the low battery. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 50 | Define a battery level as the low battery. |
Parameter 41: Enable send central scene notification.
Enable send central scene notification. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | when value is 0, it can not be send scene notification;when the value is 1,it can be send central scene notification. |
Parameter 42: Setting the duration value of the command switch multilevel
set the value of the command switch multilevel Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| -128 - 127 | The higher the value, the longer the duration value of the command. |
Parameter 43: Enable/disable the buzzer alarm when battery is running low.
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | When value is 1,it will can allow the buzzer when battery is running low;When value is 0,it will can not allow the buzzer when battery is running low |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Wall Controller |
| Network Operation | Portable Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18036040 |
| Z-Wave Product Id | 0x0371.0x0102.0x0004 |
| Z-Wave Scene Type | Central Scene |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |