GUARDTEC
GKT-1000A
SKU: GKT-1000A
Quickstart
This is a
1. Set the controller in inclusion mode.2. Press the [*] button.3. Press the Master Pin [1234] button after pressing the [#] button.4. press the [88] button after pressing the [*] button.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The GKT-1000A Z-Wave is a secure electronic door look that supports the Z-Wave Plus standard, which is compatible with earlier version of Z-Wave.A security enabled Z-Wave Controller must be use. The GKT-1000A supports the standard security S0 and the new security standard S2.
| Reset to factory default | * Use this procedure only in the event that the network primary controller is missingor otherwise inoperable.1. Press the [*] button.2. Press the Master Pin [1234] button after pressing the [#] button.3. press the [00] button after pressing the [*] button. |
| Inclusion | 1. Set the controller in inclusion mode.2. Press the [*] button.3. Press the Master Pin [1234] button after pressing the [#] button.4. press the [88] button after pressing the [*] button. |
| Exclusion | 1. Set the controller in exclusion mode.2. Press the [*] button.3. Press the Master Pin [1234] button after pressing the [#] button.4. press the [99] button after pressing the [*] button. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Doorlock Op |
Configuration Parameters
Parameter 1: Auto Relock
1=Auto, 2=Manual Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 2 | 1=Auto, 2=Manual |
Parameter 2: Relock Time
Relock Time 1~60 sec. Size: 1 Byte, Default Value: 7
| Setting | Description |
|---|---|
| 1 - 60 | 1~60 sec. |
Parameter 3: Sound
1=Mute, 2=Normal, 3=Max Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 - 3 | 1=Mute, 2=Normal, 3=Max |
Parameter 4: Sencer Type
1=NO, 2=NC Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 2 | 1=NO, 2=NC |
Parameter 5: Alarm
1=Enable, 2=Disable Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 - 2 | 1=Enable, 2=Disable |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Door Lock - Keypad |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.01:01.01 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18026032 |
| Z-Wave Product Id | 0x037B.0x0001.0x0001 |
| Supported Notification Types | Access ControlEmergency AlarmHome Security |
| Communications Connections | Bluetooth |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |