LEEDARSON
EU Smart Plug
SKU: 6A-PL-VAB-C0
Quickstart
This is a
1.Set the Z-Wave network main controller into learning mode.2.Short press the Z-button twice3.The LED keep blink to the end of add inclusion, If the add for inclusion is successful, LED will turn on within 2 seconds and Then will be in power indication mode, Otherwise, The LED will keep slow flash.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Smart Plug can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.If you want your Smart Plug to be a security device that use secure/encrypted message to communicate in a Z-Wave network, then a security enabled Z-Wave controller is needed.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Reset Smart Plug to factory Default:1.Make sure that the Smart Plug has been connected to the power supply.2.Press and hold the Z-button for 5 seconds.3.If holding time is more than one second, the LED will blink faster and faster. If holding time is more than 5 seconds, the LED will be solid for 3 seconds to indicate that the resetting is successful. Otherwise, repeat step 2. Use this procedure only in the event that the network primary controller missing or otherwise inoperable.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
1.Set the Z-Wave network main controller into learning mode.2.Short press the Z-button twice3.The LED keep blink to the end of add inclusion, If the add for inclusion is successful, LED will turn on within 2 seconds and Then will be in power indication mode, Otherwise, The LED will keep slow flash.Exclusion
1.Set the Z-Wave network main controller into removing mode.2.Short press Z-button twice.3.The LED keep blink to the end of remove exclusion, If the remove for exclusion is successful, The LED will keep slow flash, Otherwise, LED will be in power indication mode.Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | 1. When the state of Smart Plug (turn on or off the load) is changed:1.Set Configuration parameter 0x03 to 0:Do not send Basic Report2. Set Configuration parameter 0x03 to 1: Send Basic Report3. Set Configuration parameter 0x03 to 2: Send Basic Report only when Load condition is changed not by Z-WAVE Command, such as short pressing.2. Sending Meter Report. |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Over current protection
Smart Plug keep detecting the load power, once the AC current exceeds 16A for more than 5s, smart plug's relay will turn off. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled |
| 1 | The function is enabled. |
Parameter 100: Setting the parameters 101~104 to the default value.
Setting the parameters 101~104 to the default value. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 85 | Setting the parameters 101~104 to the default value. |
Parameter 101: Setting time for sending meter report (watt)
The interval time of sending meter report (watt) to associated device (Group Lifeline). Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled. |
Parameter 102: Setting time for sending meter report (KWh)
The interval of sending meter report (KWh) to association device (Group Lifeline). Size: 4 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled. |
Parameter 103: Setting time for sending meter report (voltage)
The interval of sending meter report (voltage) to association device (Group Lifeline). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled |
Parameter 104: Setting time for sending meter report (current)
The interval time of sending meter report (current) to associated device (Group Lifeline). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled |
Parameter 16: The value here represents minimum change in wattage (in terms of wattage) for a meter report to be sent
When the change value of load power exceeds the setting value, smart plug will send meter report (watt)to associated device (Group Lifeline). Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 1 - 65535 | Available settings |
| 0 | The function is disabled. |
Parameter 17: The value here represents minimum change in wattage percent (in terms of percentage) for a meter report (watt) to be sent
When the change value of the load power exceeds the setting value, smart plug will send meter report to associated device (Group Lifeline). Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| -128 - 127 | Available setting |
| 0 | The function is disabled. |
Parameter 2: Setting device status after power failure
Define how the Plug reacts after the power supply is back on. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Smart Plug memorizes its state after a power failure. |
| 1 | Connected device will be on after the power supply is reconnected. |
| 2 | Connected device will be off after the power supply is reconnected. |
Parameter 254: Enable/disable the configuration command
Lock/unlock all configuration parameters. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unlock |
| 1 | Lock |
Parameter 3: Notification when Load status change
Smart Plug can send notifications to associated device (Group Lifeline) when the status of smart plugs load is changed. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 1 | Send Basic report. |
| 2 | Send Basic report only when Load status is not changed by Z-WAVE Command. |
Parameter 4: LED Load indicator mode selection
Configure LED Display mode to prevent light pollution at night. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The LED status follows the load change. |
| 1 | when operating the load, The LED lights for 5 seconds and then turns off. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18015958 |
| Z-Wave Product Id | 0x0300.0x0200.0x000B |
| Supported Meter Type | Electric Energy |
| Switch Type | Push Button |
| Z-Wave Scene Type | Scene |
| Firmware Updatable | Updatable by Consumer by RF |
| Security V2 | S2_UNAUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Basic
- Configuration
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Meter V3
- Powerlevel
- Scene Activation
- Scene Actuator Conf
- Security
- Security 2
- Supervision
- Switch Binary
- Transport Service V2
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.