Quickstart

This is a secure Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
1. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on how to turn your controller into inclusion).2. Power on the LED dimmer, make sure the LED dimmer does not belong to any Z-Wave network (please refer to the part How to check whether the LED dimmer included to a network of this manual).1) When the connected LED light flashes quickly for 6 seconds, it means the LED dimmer does not belong to any network. Triple press the Inclusion/Exclusion button, it will be set into inclusion mode automatically, and waiting to be included.2) When the connected LED light is under solid on status, it means the LED dimmer has already been included into a network. First you have to set the LED dimmer into exclusion mode, once excluded, it will be set into inclusion mode automatically, and waiting to be included.The connected LED light stays solid on 3s to indicate successful inclusion.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

The LED dimmer is a Z-Wave device that is used to switch ON/OFF and adjust light intensity of the connected LED light and can be controlled by other Z-Wave devices. The dimmer can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-batteryoperated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.the device cannot act as Z-Wave network controller (primary or secondary), so a security enabled controller is needed for take full advantage of all functionally for the device. It also supports the Over The Air (OTA) feature for the products firmware upgrade.The encryption modes that the LED dimmer supports are S0, S2 unauthenticated. When the LED dimmer is being included into a Z-Wave network, you can use your primary controller/gateway to enable one encryption mode or disable encryption. (The primary controller/gateway shall support encryption mode configuration).

Reset to factory default	Press and hold down inclusion/exclusion button for over 10 seconds, connected LED light stays solid on 3s to indicate successful factory reset, release inclusion/exclusion button, all 4 PWM outputs will restore to 50% brightness.
Inclusion	1. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on how to turn your controller into inclusion).2. Power on the LED dimmer, make sure the LED dimmer does not belong to any Z-Wave network (please refer to the part How to check whether the LED dimmer included to a network of this manual).1) When the connected LED light flashes quickly for 6 seconds, it means the LED dimmer does not belong to any network. Triple press the Inclusion/Exclusion button, it will be set into inclusion mode automatically, and waiting to be included.2) When the connected LED light is under solid on status, it means the LED dimmer has already been included into a network. First you have to set the LED dimmer into exclusion mode, once excluded, it will be set into inclusion mode automatically, and waiting to be included.The connected LED light stays solid on 3s to indicate successful inclusion.
Exclusion	There are two exclusion methods:Method 1: Exclusion from the primary controller/gateway as follows:1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).2. Triple press the inclusion/exclusion button, the LED dimmer will be set to exclusion mode, the connected LED light will flash quickly for 6 seconds, and waiting to be excluded, then LED light stays solid on 3s to indicate successful exclusion.There are 3 methods for the LED dimmer to quit exclusion mode. Once the LED dimmer quits exclusion mode, the LED light will stop the fast flash status.1. Automatically quits after successful exclusion.2. Quits after 10 seconds timeout.3. Power off and power on the LED dimmer.(Note: When the LED dimmer already included to a network, triple pressinclusion/exclusion button, the LED dimmer will be set into exclusion mode and quit exclusion mode alternatively.)Method 2: Factory reset the LED dimmer will force the LED dimmer to be excluded from a network. (please refer to the part Factory Reset of this manual)Note: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	5	Z-Wave Plus Lifeline

Configuration Parameters

Parameter 2: Saving load state before power failure

Saving load state before power failure
Size: 1 Byte, Default Value: 0

Setting Description
0 shutoff load

1 turn on load

2 save load state before power failure

Setting	Description
0	shutoff load
1	turn on load
2	save load state before power failure

Parameter 3: Enable/disable to send the basic report

Enable/disable to send the basic report to the Lifeline when the load state changed (When value set as 1, re-power on the dimmer, it will send Basic report automatically
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable to send Basic report

1 Enable to send Basic report

Setting	Description
0	Disable to send Basic report
1	Enable to send Basic report

Parameter 4: Select the type of the light band

Select the type of the light band
Size: 1 Byte, Default Value: 2

Setting Description
0 single color light band, 4 channels PWM output to drive 4 channels single color light band

1 CCT light band, 2 channels PWM output, R(B) controls warm white, G(W) controls cool white

2 RGBW light band, 4 channels PWM output to drive RGBW light band

Setting	Description
0	single color light band, 4 channels PWM output to drive 4 channels single color light band
1	CCT light band, 2 channels PWM output, R(B) controls warm white, G(W) controls cool white
2	RGBW light band, 4 channels PWM output to drive RGBW light band

Parameter 5: Choose a cool light stage mode

receiving Command Class Switch Color, or switching light band type, it recovers to normal lighting mode.)Remarks: When parameter number 4 is set as single color light band, the valid values of this parameter are 0~2.
Size: 1 Byte, Default Value: 0

Setting Description
0 inactive of light stage mode

1 fade in and fade out mode, colors set by parameter 8

2 flash mode, colors set by parameter 8

3 rainbow mode, system fixed changing effect

4 fade in and fade out mode, color changes randomly

5 flash mode, color changes randomly

6 rainbow mode, color changes randomly

7 random mode, the colors switch randomly

Setting	Description
0	inactive of light stage mode
1	fade in and fade out mode, colors set by parameter 8
2	flash mode, colors set by parameter 8
3	rainbow mode, system fixed changing effect
4	fade in and fade out mode, color changes randomly
5	flash mode, color changes randomly
6	rainbow mode, color changes randomly
7	random mode, the colors switch randomly

Parameter 6: Speed of stage mode

Speed of stage mode
Size: 1 Byte, Default Value: 243

Setting Description
0 - 255 0 is the slowest, 255(0xFF) is the fastest

Setting	Description
0 - 255	0 is the slowest, 255(0xFF) is the fastest

Parameter 7: Execution times of stage mode

Execution times of stage mode
Size: 1 Byte, Default Value: 0

Setting Description
0 unlimited times

1 - 255 1~0xFF, execution times 1~255

Setting	Description
0	unlimited times
1 - 255	1~0xFF, execution times 1~255

Parameter 8: The hue of stage mode

The hue is only valid for fade in and fade outmode, flash mode
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 0~0xFF value of hue,only valid for fade in and fade out mode, flash mode

Setting	Description
0 - 255	0~0xFF value of hue,only valid for fade in and fade out mode, flash mode

Parameter 9: Enable/disable external switch to be added to and removed from a network

Enable/disable external switch to be added to and removed from a network (when enables this function, triple press the external switch within 1.5 seconds to be added to or removed from a network)
Size: 1 Byte, Default Value: 0

Setting Description
0 disable

1 enable

Setting	Description
0	disable
1	enable

Technical Data

Hardware Platform	ZM5101
Device Type	Light Dimmer Switch
Network Operation	Always On Slave
Firmware Version	HW: 1 FW: 1.00
Z-Wave Version	6.71.01
Certification ID	ZC10-18015928
Z-Wave Product Id	0x0330.0x021A.0xD002
Supported Notification Types	System
Firmware Updatable	Updatable by Consumer by RF
Frequency	Russia - 868.4MHz, 869.85MHz
Maximum transmission power	5 mW

Sunricher

LED Dimmer

SKU: SR-ZV9101FX-RU