This is a
1. Follow the instructions for your Z-Wave certified controller toinclude a device to the Z-Wave network.2. Once the controller is ready to add your device,press and release the top or bottom of the wireless smartswitch (rocker) to add it in the network.Please reference the controllers manual for instructions.
Transform any home into a smart home with the Honeywell In-WallDimmer. The In-Wall Dimmer can easily replace any standard in-wall switch and remotely controls a light in your home. Your home will be equipped with ultimate flexibility with the Honeywell Z-Wave Dimmer, capable of being used by itself or with up to four add-on switches. Screw terminal installation provides improved space efficiency when replacing existing switches and the integrated LED indicator light allows you to easily locate the switch in a dark room. The Honeywell Z-Wave In-Wall Dimmer is compatible with any Z-Wave certified gateway, providing access to many popular home automation systems. Take control of your home lighting with Honeywell Z-Wave Smart Controls!
Reset to factory default | Quickly press ON (Top) button three (3) times then immediatelypress the OFF (Bottom) button three (3) times. The LED will flashON/OFF 5 times when completed successfully.NOTE: This should only be used in the event your networksprimary controller is missing or otherwise inoperable. |
Inclusion | 1. Follow the instructions for your Z-Wave certified controller toinclude a device to the Z-Wave network.2. Once the controller is ready to add your device,press and release the top or bottom of the wireless smartswitch (rocker) to add it in the network.Please reference the controllers manual for instructions. |
Exclusion | 1. Follow the instructions for your Z-Wave certified controller toremove a device from the Z-Wave network.2. Once the controller is ready to Exclude your device, pressand release the top or bottom of the wireless smart dimmer(rocker) to remove it from the network. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline, Multilevel Switch Report |
2 | 5 | Support Basic Set and is controlled with the local load |
3 | 5 | Supports Basic Set and is controlled by double pressing the On or Off button |
Dim Rate Adjustments when manually controlling dimming Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | timing of steps |
Dim Rate Adjustments when receiving an All-On or All-Off command Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | number of steps or levels |
Dime Rate Adjustments when receiving an All-On or All-Off command Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | timing of steps |
When shipped from the factory, the LED is set to turn ON when the connected light is turned OFF. This is the default setting and can be changed if your primary controller supports the node configuration function. To make the LED turn ON when the light is turned ON, change parameter 3s value to 1. To turn the LED OFF at all times, change parameter 3s value to 2. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Default |
1 | LED ON when load is ON |
2 | LED always OFF |
If the switch is accidentally installed upside down with On at the bottom and Off at the top, the default On/Off rocker settings can be reversed by changing parameter 4s value to 1. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Default |
1 | Invert Switch |
Dim Rate Adjustments when receiving Z-Wave dim command Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | number of steps or levels |
Dim Rate Adjustments when receiving a Z-Wave dim command Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | timing of steps |
Dime Rate Adjustments when manually controlled dimming Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | number of steps or levels |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 5.28 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-17125898 |
Z-Wave Product Id | 0x0039.0x4944.0x3038 |
Color | White |
Switch Type | Decorator Paddle Rocker |
Neutral Wire Required | ok |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |