GE
Plug-in Dual Smart Switch, Independant Control With USB Charging
SKU: 28177/ZW4105
Quickstart
This is a
1. Follow the instructions for your Z-Wave certified controller toadd the device to the Z-Wave network.2. Once the controller is ready to add your smart switch,single press and release the manual/program button on thesmart switch to add it in the network.3. Once your controller has confirmed that the smart switchhas been added, refresh the Z-Wave network to optimizeperformance.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Transform any home into a smart home with the GE Z-Wave Plug-in Dual Smart Switch With 3.4A USB Charging. This module enable wireless control on on/off functions for standard incandescent table and floor lamps, compatible with incandescent, LED, Xenon, Halogen, fluorescent and compact and more! Use the switch control to customize the lighting output and create the perfect ambiance for any room. The space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. This module also enables you to have independent or simultaneous control of each outlet! Take control of your home lighting with GE Z-Wave Smart Lighting Controls!
| Reset to factory default | 1. If plugged in, unplug the Switch from the receptacle.2. Press and hold the top button for at least 3 seconds while youplug the switch into a receptacle.Note: This should only be used in the event your networksprimary controller is missing or otherwise inoperable. |
| Inclusion | 1. Follow the instructions for your Z-Wave certified controller toadd the device to the Z-Wave network.2. Once the controller is ready to add your smart switch,single press and release the manual/program button on thesmart switch to add it in the network.3. Once your controller has confirmed that the smart switchhas been added, refresh the Z-Wave network to optimizeperformance. |
| Exclusion | 1. Follow the instructions for your Z-Wave certified controller toremove a device from the Z-Wave network.2. Once the controller is ready to remove your device, press andrelease the manual/program button on the smart switch toremove it from the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Group 2 supports Basic Set and is controlled with the local load |
| 3 | 5 | Group 3 supports Basic Set and is controlled by double pressing the On or Off button |
Configuration Parameters
Parameter 3: LED Light
When shipped from the factory, the LED is set to turn ON when the connected light is turned On. This is the default setting and can be changed if your primary controller supports the node configuration function. To make the LED turn ON when the light is turned Off, change parameter 3s value to 1. To turn the LED OFF at all times, change parameter 3s value to 2.Parameter No: 3Length: 1 ByteValid Values = 0, 1 or 2 (default 0) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | LED Light On when deivce is Off |
| 2 | LED Light Always On |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.23 |
| Z-Wave Version | 6.51.10 |
| Certification ID | ZC10-17105795 |
| Z-Wave Product Id | 0x0063.0x5052.0x3132 |
| Firmware Updatable | Updatable by Consumer by RF |
| Loads Controlled | 2 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |