This is a
1. Connect the module to the power supply2. Enable inclusion mode on your Z-Wave controller3. Press and release the S (Service) button 3 times within 2 seconds
Qubino Flush RGBW module is used to control RGB/RGBW strips and LED strips or bulbs to create countless colour options and has 5 special scene effects. It can also control halogen lights and fans. Its extremely small size allows for easy installation behind wall sockets and switches. Controlled devices may be powered by 12 or 24 VDC. All IN and OUT terminals may be user configured for LED control or 100 k signal readouts.
Reset to factory default | FACTORY RESET1. Connect the module to the power supply2. Press and hold the S (Service) button for at least 10 secondsNOTE: By resetting the module, all custom parameters previously set on the module will return to their default values, and owner ID will be deleted. Use this reset procedure only when the main controller is missing or otherwise inoperable. |
Inclusion | 1. Connect the module to the power supply2. Enable inclusion mode on your Z-Wave controller3. Press and release the S (Service) button 3 times within 2 seconds |
Exclusion | 1. Connect the module to the power supply2. Make sure the module is within direct range of your Z-Wave controller or use a hand-held Z-Wave remote to perform exclusion3. Press and release the S (Service) button 3 times within 2 secondsNOTE: The module will be excluded from your network, but any custom configuration parameters will not be erased. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline |
Available config. parmeters(data type is 1 Byte DEC):* default value 1* 1- bi- stable switch type* 2- mono stable(push button) switch typeNote: Please power cycle the device when parameter is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 2 | Input Switch type |
Available config. parmeters(data type is 1 Byte DEC):* default value 1* 1-Normal mode* 2-Brightness mode* 3-Rainbow modeNote: Using this parameter,it is possible to select various modes of RGBW Dimmer operation. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 3 | Switch mode |
Available config. parmeters(data type is 1 Byte DEC):* default value-* 1-Ocean* 2-Lightning* 3-Rainbow* 4-Snow* 5-SunNote: Activation of the programmed scene changing color shades.Note: Using this parameter,it is possible to select various modes of RGBW Dimmer operation. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 - 5 | Auto Scene mode set |
Available config. parmeters(data type is 1 Byte DEC):* default value 3* 1 -127* 128 - 255 delay duration is from 1 min. to 127minNote: Using this parameter, it is possible to change Auto scene mode duration Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 127 | delay duration is from 1s to 127s |
128 - 255 | delay duration is from 1 min. to 127 min. |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 2.07 |
Z-Wave Version | 6.51.07 |
Certification ID | ZC10-17085753 |
Z-Wave Product Id | 0x0159.0x0001.0x0054 |
Color | Blue |
Firmware Updatable | Updatable by Manufacturer |
Electric Load Type | Dimmable LED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |