Aeotec
Door/ Window Sensor 6
SKU: ZW112-D
Quickstart
This is a
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action Button that you can find in the back of the product.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeon Labs Door/ Window Sensor 6 is a smart Z-Wave sensor that can detect the status of door/window's open/close in real time. Its a security Z-Wave device that supports security encryption. Also it supports the Over the Air Firmware Updating that allows you wirelessly update its firmware if needs. It can be included and operated in any Z-Wave network with other Z-Wave certified devices from manufacturers and/or other applications.
| Reset to factory default | Press the Action Button once that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. |
| Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action Button that you can find in the back of the product. |
| Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, short press the products Action Button that you can find in back of the product. |
| NIF | XXXNIF |
| Wakeup | Press the Action Button once, which will trigger sending out the Wake up notification command, press and hold the Action Button for 3 seconds, which will toggle on/off the Sensor be waked up for 10 minutes. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate. The sensor binary report, basic set or notification report command can be sent in this group when the Sensor is triggered. |
Configuration Parameters
Parameter 1: Which value of the Sensor Binary Report or Basic Set will be sent when the door is Opened/Closed.
To set which value of the Sensor Binary Report or Basic Set will be sent when the door is Opened/Closed. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Sensor Binary Report/Basic Set =0xFF when the door is opened, Sensor Binary Report/Basic Set= 0x00 when the door is closed. |
| 1 | Sensor Binary Report/Basic Set= 0x00 when the door is opened, Sensor Binary Report/Basic Set=0xFF when the door is closed. |
Parameter 101: Enable/disable the function of parameter 111
Enable/disable the function of parameter 111.Note: this parameter cannot disable the low battery checking of the Sensor itself. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable. |
| 1 | Enable. |
Parameter 111: Set the interval time of low battery checking.
Set the interval time of low battery checking.Note:1, if the value is less than 10, the time unit is second.If the value is more than 10, the time unit is 4 minutes, which means if the value is more than 10 and less than 240, the interval time is 4 minutes. If the value is more than 240 and less than 480, the interval is 8 minutes.2, if the current battery report falls below the low battery value (configurable parameter 39), it will send battery report=0xFF. Size: 4 Byte, Default Value: 86640
| Setting | Description |
|---|---|
| 0 - 2147483647 | The range of interval can be set to 0 to 2147483647. |
Parameter 121: To configure which sensor report will be sent when the door is opened/closed.
To configure which sensor report will be sent when the door is opened/closed. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Basic Set CC is selected. |
| 2 | Sensor Binary Report CC is selected. |
| 3 | Basic Set CC and Sensor Binary Report CC are selected. |
Parameter 252: Lock/unlock all configuration parameters.
Lock/unlock all configuration parameters. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unlock. |
| 1 | Lock. |
Parameter 255: Reset the Sensor.
Reset the Sensor. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Reset to default settings. |
| 1431655765 | Reset to default settings and excluded from the network. |
Parameter 39: Set the low battery value.
Set the low battery value.(10% to 50%). Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 50 | The range of low battery value can be set to 10% to 50%. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 112 FW: 1.03 |
| Z-Wave Version | 6.51.09 |
| Certification ID | ZC10-17085746 |
| Z-Wave Product Id | 0x0086.0x0302.0x0070 |
| Sensors | Open/Closed (Binary) |
| Supported Notification Types | Access Control |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |