GoControl
WI15VZ-1 Smart Irrigation Controller
SKU: WI15VZ-1
Quickstart
This is a
When the WI15VZ-1 is first powered up, the Status LED should be Red. If the Status LED is Green, the WI15VZ-1 needs to be reset (see below). To add it to your network refer to your controller operating instructions.1. With your controller in Discovery or Add Mode, tap the button (See Figure8).2. You should see an indication on your controller that the device was added to the network and the Green LED will blink. The device will appear in the list of switches. It should display as a switch. If the controller shows the addition failed, repeat Steps 1-3.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The WI15Z5-1 Smart Irrigation Controller supports up to 15 valves using the Irrigation Command Class.A Z-Wave hub can use local weather conditions and connected rain and moisture sensors to optimizes the use of the scheduled watering cycles.As a connected device, sprinklers can be turned on or off from anywhere there is internet connectivity.Integrated diagnostics and flow sensor support help determine breaks or improper operation of the irrigation system.
| Reset to factory default | In the event that your Hub is lost or otherwise inoperable, to reset the GoControl Irrigation Controller and clear all network information, follow these steps:1. Tap the button five (5) times.2. Then press and hold the button for 15 seconds. The Status LED willincreasingly blink faster to indicate that a Reset is taking place. |
| Inclusion | When the WI15VZ-1 is first powered up, the Status LED should be Red. If the Status LED is Green, the WI15VZ-1 needs to be reset (see below). To add it to your network refer to your controller operating instructions.1. With your controller in Discovery or Add Mode, tap the button (See Figure8).2. You should see an indication on your controller that the device was added to the network and the Green LED will blink. The device will appear in the list of switches. It should display as a switch. If the controller shows the addition failed, repeat Steps 1-3. |
| Exclusion | The GoControl Irrigation Controller can be removed from the network by the controller. Refer to the controller operating instructions for details.1. Set the controller into Removal Mode and follow its instructions to delete it from the controller.2. Remove the Irrigation Controller by tapping the button 2 times.3. You should see an indication on your controller that the device wasremoved from the network and the Green LED will blink then turn Red. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 12: Flow Sensor K value
Used to enter in the unique K Factor of an optional flow sensor.Refer to the flow sensor manual for this entry. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unique to flow sensor |
Parameter 13: Flow Sensor Offset value
Used to enter in the unique Offset Value of an optional flow sensor.Refer to the flow sensor manual for this entry. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unique to the flow sensor |
Parameter 2: Master Valve Delay
A 3rd party Master Valve/Pump can connect directly to the inputs of theIrrigation Controller. If the Master Valve is using a relay to drive a pump, therelay coil needs to be rated for 24VAC at up to 15W. Some systems requirea delay time for the pump to pressurize the water. Size: 2 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 - 255 | Delay in seconds |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Irrigation Control |
| Network Operation | Always On Slave |
| Firmware Version | HW: 2 FW: 99.12 |
| Z-Wave Version | 6.51.08 |
| Certification ID | ZC10-17075704 |
| Z-Wave Product Id | 0x014F.0x5749.0x3135 |
| Supported Notification Types | Irrigation |
| Color | Black |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |