Quickstart
This is a
Window Covering - Endpoint Aware for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
Follow the directions for your Z-Wave hub/controller to place it in the add for inclusion mode. Press the inclusion button once and wait for the device to be discovered and joined to the Z-Wave network.Follow the directions of your Z-Wave controller to uniquely identify your iblinds device. (Ex: Bedroom iblind)Note: If the device is not joined to the network.Press the CLBR button Wait 1 minutes and repeat steps 1 and 2 again.If you continue to have trouble joining the iblinds motor to the Z-Wave network follow the Z-Wave network Exclusion process below.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
An intelligent Z-Wave blind motor that installs out of sight in existing Horizontal (2" and 2 1/2" slatted-style) blind headrails. Use iBlinds to tilt the slats open, closed or use the value slider for precise positioning of the slat tilt angle.
Reset to factory default |
The Device Reset Locally function is used to reset the device to fatory defalut.The reset operation resets protocol data (HomeID, NodeID) as well as all application specific data to factory default values.vice Reset LocallyNOTE: Please only use this function when the primary controller is missing or inoperable! 1.Press the INC / EXC button 3Press the INC / EXC button 3 times within 5 seconds to enable the device reset function.2.Wait 30 Seconds Press CLBR buttonAfter device is reset wait 30 seconds and press the CLBR button to reboot the device and make it ready for Z-Wave Inclusion. |
Inclusion |
Follow the directions for your Z-Wave hub/controller to place it in the add for inclusion mode. Press the inclusion button once and wait for the device to be discovered and joined to the Z-Wave network.Follow the directions of your Z-Wave controller to uniquely identify your iblinds device. (Ex: Bedroom iblind)Note: If the device is not joined to the network.Press the CLBR button Wait 1 minutes and repeat steps 1 and 2 again.If you continue to have trouble joining the iblinds motor to the Z-Wave network follow the Z-Wave network Exclusion process below. |
Exclusion |
Follow the directions for your Z-Wave device to place it in the exclusion mode. Press the exclude button once and wait for the device to be removed from the Z-Wave network. |
NIF |
XXXNIF |
Wakeup |
XXXWakeupDescription |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
1 |
5 |
Z-Wave Plus Lifeline |
Technical Data
Hardware Platform |
ZM5202 |
Device Type |
Window Covering - Endpoint Aware |
Network Operation |
Listening Sleeping Slave |
Firmware Version |
HW: 255 FW: 1.65 |
Z-Wave Version |
6.61.00 |
Certification ID |
ZC10-17075690 |
Z-Wave Product Id |
0x0287.0x0003.0x000D |
Window Covering Control Features |
Automatic CalibrationEndpoint AwarePosition AwareSupports Horizontal Blinds/LouversSupports Open/Close MotionSupports Tilt Motion |
Color |
Black |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |