Vision
4 in 1 Door Sensor
SKU: ZD2201JP-5
Quickstart
This is a
For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZD2301 to your controller, to get in the inclusion mode. Press the program switch of ZD2301 for sending the NIF.After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Visions wireless 4 in 1 Multi-Sensor (door window contact sensor, humidity sensor, temperature sensor, and light sensor) of the home security device. This multi-sensor sends Z-Wave signal when door or window is opened and closed or humidity, temperature, luminous change.When the device is secure included into Z-Wave network, above communication will be encrypted.
| Reset to factory default | Factory Default Reset: *Open the rear cover to send the Alarm Report and then press the program switch 10 times in 10 seconds, ZD2301 will send the Device Reset Locally command and reset to the factory default. * Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | For Inclusion in (adding to) a network: Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the ZD2301 to your controller, to get in the inclusion mode. Press the program switch of ZD2301 for sending the NIF.After sending NIF, Z-Wave will send the auto inclusion; otherwise, ZD2301 will go to sleep after 20 seconds. |
| Exclusion | For Exclusion from (removing from) a network: Put the Z-Wave Interface Controller into exclusion mode, and following its instruction to delete the ZD2301 from your controller.Press the program switch of ZD2301 for 1 second at least to be excluded. |
| NIF | XXXNIF |
| Wakeup | Use Wake Up command to set up the awaking time and send the wake up notification to controller.User can use command to change the auto wake up from 10 minutes to 1 week, Interval increment is 3 minutes. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline |
Configuration Parameters
Parameter 1: Temperature Unit Selection
0x00 = C0x01 = F Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | Choose F |
Parameter 2: Auto Temperature Report Interval
1~50 (Set up from 0.1C~5C) Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 1 - 50 | Auto Temperature Report Interval from 0.1C~5C |
Parameter 3: Auto Humidity Report Interval
1~50 (Set up from 1%~50%) Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 1 - 50 | Auto Humidity Report Intervalfrom 1%~50% |
Parameter 4: Auto Light Report Interval
0,5~50 (Set up from 0 for Off or 5%~50%) Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 50 | Auto Light Report Interval from Off or 5%~50% |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 5 FW: 6.01:10.01 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-17075681 |
| Z-Wave Product Id | 0x0109.0x201F.0x1F10 |
| Supported Notification Types | Access Control |
| Sensors | Open/Closed (Binary) |
| Color | White |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |