This is a
Follow the instructions for your Z-Wave certified Controller to enter inclusion mode.When prompted by the Controller:1. For proper inclusion, bring the Siren within range of your Controller.2. Pull the tab on the side of the siren to power on, or remove then re-install the batteries.The LED Ring willflashfive times indicating inclusion.
The Wink Siren is a Z-Wave Plus battery-powered device that will sound an alarm, chime, and flash a built-in light to let you know when doors and windows open or when motion is detected in your home. The sirens multi-purpose functionality of an alarm siren, doorbell, or chime notification can be turned on and off manually or automatically from your smartphone using a Wink Hub or other Z-Wave Plus certified hub. The Wink Siren offers ten user selectable sounds for alarm and chime, with three volume levels (up to 105dB) and adjustable siren duration timeout. Additional visual notification is provided by built-in flashing blue LEDs when triggered. The Wink Siren offers an extra-long z-wave wireless range of up to 150 feet, so you can place it in your home where its needed, and requires a Wink Hub or other Z-Wave Plus certified hub for operation. The siren comes with two CR123A 3.0V batteries and has a three-year battery life, and will send an alert to your smartphone when the device has low battery. Z-Wave Plus CertifiedRequires a Z-Wave Plus Certified Hub to operateWorks with all Z-Wave Plus compatible networks110 Extra-Wide Coverage AreaUp to 150 feet rangeThree-Year Battery Life (Two CR123 Batteries included)Low Battery IndicationMeasurements in millimeters: 64.3 x 64.3 x 30.1
Reset to factory default | To disconnect from the Z-Wave Network and restore factory default settings:1. Remove the Back Plate and make sure the Siren is powered.1. Hold the Connect Button for 10 seconds until the LED Ring blinks once, then release the button.Only do this if the controller is missing or otherwise unreachable! |
Inclusion | Follow the instructions for your Z-Wave certified Controller to enter inclusion mode.When prompted by the Controller:1. For proper inclusion, bring the Siren within range of your Controller.2. Pull the tab on the side of the siren to power on, or remove then re-install the batteries.The LED Ring willflashfive times indicating inclusion. |
Exclusion | Follow the instructions for your Z-Wave certified Controller to enter exclusion mode.When prompted by the Controller:1. Remove the Back Plate of the Siren and be sure it is powered on2. Press the Connect Button quickly 3 times in a row.The LED Ring will flash five times indicating exclusion/disconnection. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Group 1 is the Lifeline group, which can hold five members, typically including the main Z-Wave controller. The Siren sends this group a Notification Report and a Binary Switch Report when the siren is turned on or off. It also sends this group a Battery Report in reponse to Battery Get commands and a Locally Reset Notification upon local reset. |
2 | 5 | Group 2 can hold five members, and the Siren sends a single command to this Association Group, the Binary Switch Report, whenever the Siren is turned on or off. |
3 | 5 | Group 2 can hold five members, and the Siren sends a single command to this Association Group, a Notification Report, whenever the Siren is turned on or off. |
This parameter sets the volume of the Siren (primary) sound. There are three possible volume levels available. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
1 | Low Volume |
2 | Medium Volume |
3 | High Volume |
This parameter defines the length of the Alarm/primary notification. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
-1 | Plays until battery dies |
1 | 30 Sec |
2 | 1 Min |
3 | 5 Min |
This parameter defines the length of the Chime/secondary notification. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
-128 - -2 | Chime Duration (in Minutes; -128=128 min, -2=254 min) |
-1 | Chime Will Not Play |
0 | Does Not Stop |
1 - 127 | Chime Duration (in Minutes) |
This parameter sets the volume of the Chime (secondary) sound. There are three possible volume levels available. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
1 | Low Volume |
2 | Medium Volume |
3 | High Volume |
The Siren offers ten different sounds to use as the Siren (primary) notification. This parameter sets the Siren (primary) notification sound. Size: 1 Byte, Default Value: 9
Setting | Description |
---|---|
1 - 10 | Tone Index Number |
If Parameter 7 is set to 02, the Siren will play a secondary chime sound instead of the main alarm. The Siren offers ten different sounds to use as the Chime (secondary) notification. This parameter sets the Chime (secondary) notification sound. Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
1 - 10 | Tone Index Number |
This Parameter toggles between the Primary and Secondary notification sound to be played when the Siren receives a BINARY_SWITCH_SET(FF) command. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Primary Notification Will Play |
2 | Secondary Notification Will Play |
Hardware Platform | ZM5202 |
Device Type | Siren |
Network Operation | Listening Sleeping Slave |
Firmware Version | HW: 48 FW: 2.65 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-17065664 |
Z-Wave Product Id | 0x017F.0x0200.0x0001 |
Supported Notification Types | |
Color | |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |