This is a
Step 1)Start the gateway inAdd device mode.Step 2) Trigger module start "DeviceAdd/Remove" mode by program button on the module or local switch connected to the module as following: a)By program button on the module: Quick pressing the program button 3 times in 1.5 seconds ( LED quick flashing ) to enter Device Add/Remove mode. LED lights up for 3 sec to indicate Add process complete.b)By switch connected to the module (only available after 10 mins of AC power on ): Rocker Switch: Quick toggle channel 1 or channel 2 switch turn on and off 5 times( LED quick flashing ) to enter Device Add/Remove mode. LED lights up for 3 sec to indicate Add process complete.Momentary Switch: Quick pressing channel 1 or channel 2 switch button 5 times ( LED quick flashing ) to enter Device Add/Remove mode. LED lights up for 3 sec to indicate Add process complete.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
2 Gang Insert Module Switch is designed to operate without neutral wire. It operates with different loads, including Incandescent lamps, halogen lamps or LEDS. It can act as repeaters regardless of vendor to increase reliability of the network.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press and hold the program button for 10 sec, LED lights up for 3 sec to indicate the factory default reset complete.Note:Please use this procedure only when the network primary controller is missing or otherwise inoperable.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | This group is dedicated for device status reporting to gateway/master controller Z-Wave command class:SWITCH BINARY REPORTDEVICE_RESET_LOCALLY_NOTIFICATION |
2 | 2 | This group is dedicated for load 1 on, BASIC SET ON command will be sent out when load 1 is turned on |
3 | 2 | This group is dedicated for load 1 off, BASIC SET OFF command will be sent out when load 1 is turned off |
4 | 2 | This group is dedicated for load 2 on, BASIC SET ON command will be sent outwhen load 2 is turned on |
5 | 2 | This group is dedicated for load 2 off, BASIC SET OFF command will be sent out when load 2 is turned off |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | Momentary switch panel |
255 | Rocker switch panel |
Rocket switch button on/off location synchronize with insert module on/off status Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
255 | Not Synchronize |
0 | Synchronize |
Default Lighting on/offwhen power turn on Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | Off |
255 | Resume last status |
Hardware Platform | ZM5202 |
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 2 FW: 2.23 |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-17065660 |
Z-Wave Product Id | 0x0111.0x5001.0x6260 |
Switch Type | Decorator Paddle Push |
Color | White |
Neutral Wire Required | ok |
Electric Load Type | |
Loads Controlled | 2 |
Outdoor Use | ok |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |