Quickstart

This is a secure Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
1. Screw the CCT bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-Wave controller or gateway.a) This may also be done through your associated app,if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/excluded into your Z-Wave network.Note: If you are using 3rd party Z-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new devices to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Our connected CCT tunable lighting has two functional categories, one is your basic On, Off and Dim, or in the lighting world, we just call it OFD. Using your app and controller/gateway, you can turn your lights on, off and dim them down to 5% brightness from anywhere in the world, using your smartphone. At 2700K and 800 lumens, it is a true 60W equivalent. Another one this is where the innovative technology takes over. You get your basic On, Off and Dim, but now you have the ability to tune the white color from a warm 2700K to a cool 6500K. The ability to tune the white is what we call Tunable White, or TW. Having this ability, and the ability from your app, you can now set the perfect scene and mood in your home. In the evening, while watching TV, you may want to tune down the white color to a warm, cozy 2700K. Or maybe your kids have homework, and its late, so to help keep their concentration, you turn the white color up to 6500K, which is similar to daylight.With all of our lighting, and the app that supports it, you can group lights together, set different lighting scenes for different groups and set schdules to autotmatically turns lights, and groups, on and off. Our connected lighting has the additional option for what we call Saved State. Saved State allows you to save an actual light setting in the bulb itself. This means that when you lose power, the lights will not come back on to the standard, blaring 2700K at full bright. The Saved State will allow the lights to come back on to the nice setting youve previously saved.LEEDARSON stays on the cutting edge of technology and innovation. Thats because they have a responsibility to their customers. Thats because at LEEDARSON, We build your success in IoT.

Reset to factory default Physically switch the bulb on and off six (6) times for intervals of 0.5-2seconds. After the 6thtime, the bulb will flash twice indicating that its successfully reset. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Inclusion 1. Screw the CCT bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-Wave controller or gateway.a) This may also be done through your associated app,if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/excluded into your Z-Wave network.Note: If you are using 3rd party Z-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new devices to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.
Exclusion 1. Screw the CCT bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-Wave controller or gateway.a) This may also be done through your associated app,if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/excluded into your Z-Wave network.Note: If you are using 3rd party Z-Wave Controller or Gateway, please refer to 3rd Partys instruction on how to add a new devices to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: get the temperature of NTC.

It was used to get the temperature of NTC.
Size: 1 Byte, Default Value: 0

Setting Description
0 - -1 It was used to get the temperature of NTC.

Parameter 255: Reset

Reset to factory configuration and removed the Z-Wave network.Reset Configuration parameter to default value.
Size: 4 Byte, Default Value: 0

Setting Description
-2013265920 Reset Configuration parameter to default value.
-2004318072 Reset to factory configuration and removed the Z-Wave network.

Technical Data

Hardware Platform ZM5101
Device Type Light Dimmer Switch
Network Operation Always On Slave
Firmware Version HW: 255 FW: 1.01
Z-Wave Version 6.51.09
Certification ID ZC10-17065649
Z-Wave Product Id 0x0300.0x0003.0x0007
Communications Protocol Manufacturer Proprietary Protocol
Firmware Updatable Updatable by Manufacturer
Frequency XXfrequency
Maximum transmission power XXantenna
CEPT (Europe)Light Dimmer Switch