This is a
Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.Pressing On/Off (Include) button three times within 2 seconds will enter inclusion mode.
This product can be operated in any Z-Wave network with other Z-Wavecertifieddevicesfromothermanufacturers.Allnon-battery operated nodes within the network will act as repeaters regardlessofvendortoincreasereliabilityofthenetwork. ZipatoEnergyMetermonitorstotalelectricityconsumption of connected appliances and reports it to Zipato or any other Z-Wave enabled controller in real time. Small and compact size allowseasyinstallationinmajorityofelectricitydistribution boxes. It supports two loads upto 6000W each (@ 120V).
Reset to factory default | Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.Pressing On/Off (Include) button three times within 2 seconds will enter inclusion mode.Within 1 second, press and hold On/Off (Include) button again for 5 seconds until LED is off.IDs are excluded. |
Inclusion | Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.Pressing On/Off (Include) button three times within 2 seconds will enter inclusion mode. |
Exclusion | Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.Pressing On/Off (Include) button three times within 2 seconds will enter exclusion mode.Node ID has been excluded. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | LifelineFor group 1, the Micromodule will report (1) The sum of instant Power Consumption (Watt) read from CT1 and CT2 (2) The sum of accumulated Power Consumption (KWh) read from CT1 and CT2. |
2 | 1 | For group 2, the Micromodule will report (1) Instant Power Consumption (Watt) read from CT1 (2) Accumulated Power Consumption (KWh) read from CT1. |
3 | 1 | For group 3, the Micromodule will report (1) Instant Power Consumption (Watt) read from CT2 (2) Accumulated Power Consumption (KWh) read from CT2. |
Ifthesettingisconfiguredfor1hour(setvalue=720), Micromodulewillreportitsinstantpowerconsumptionevery 1hourtothenodeofcorrespondGroup.Themaximum intervaltoreportitsinstantpowerconsumptionis45hours (5s*32767/3600=45hr). Size: 2 Byte, Default Value: 720
Setting | Description |
---|---|
1 - 32767 | 5*720s=3600s=1hour |
If the setting is configured for 1hour (set value =720), the PAB01 will report its Accumulated Power Consumption (KW/h) every 1 hour to the node of correspond Group. The maximum interval to report its Accumulated Power Consumption (KW/h) is 45 hours (5s*32767/3600=45hr). Size: 2 Byte, Default Value: 720
Setting | Description |
---|---|
1 - 32767 | 5*720s=3600s=1hour |
If Controller not using Multi_Channel command class to access theendpointofMicromodule,youmayconfiguretheendpoint valuetoreacttheBasicCommandClass,BinarySwitch Command Class or Meter Command Class V3. 1. SELECTED ENDPOINT 1: Report the Meter Value as CT1+CT2. Defauly selected endpoint is 1.2. SELECTED ENDPOINT 2: Report the Meter Value of CT1.3. SELECTED ENDPOINT 3: Report the Meter Value of CT2. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | 1: CT1 and CT2 |
2 | 2: CT1 |
3 | 3: CT2 |
Thisisawarningwhenthecurrentofloadoverthepreset threshold value, If the setting value is 750, when the load wattage of CT1 or CT2 over 7.5A, Micromodule will send current Meter Report command to the node of correspond Group. Size: 2 Byte, Default Value: 750
Setting | Description |
---|---|
10 - 750 | 750*0.01A=7.5A |
This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power ConsumptionofCT1orCT2overthisvalue,Micromodulewill sendKWhMeterReportcommandtothenodeofcorrespond Group, minum value is 1KWh and default value is 10000 kWh. Size: 2 Byte, Default Value: 10000
Setting | Description |
---|---|
1 - 10000 | 10000*1KWh = 10000KWh |
Hardware Platform | SD3502 |
Device Type | Whole Home Meter - Simple |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.02 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-17065646 |
Z-Wave Product Id | 0x0131.0x0006.0x001A |
Electric Load Type | Incandescent |
Firmware Updatable | Updatable by Consumer by RF |
Supported Meter Type | Electric Energy |
Color | White |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |