Micro Module motor controller

Parameter 1: Watt Meter Report Period

Ifthesettingisconfiguredfor1hour(setvalue=720),the Micromodulewillreportitsinstantpowerconsumptionevery 1hourtothenodeofcorrespondingGroup.Themaximum intervaltoreportitsinstantpowerconsumptionis45hours (5s*32767/3600=45hr). Default value is 1 hour.
Size: 2 Byte, Default Value: 720

Setting	Description
1 - 32767	5*720s=3600s=1 hour

Parameter 2: KWH Meter Report Period

Ifthesettingisconfiguredfor1hour(setvalue=6),the MicromodulewillreportitsAccumulatedPowerConsumption (KW/h)every1hourtothenodeofcorrespondingGroup.The maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55 days). Default value=1 hour.
Size: 2 Byte, Default Value: 6

Setting	Description
1 - 32767	6*10min= 1 hour

Parameter 3: Threshold of current for Load Caution

This is a warning when the wattage of load exceeds the preset thresholdvalue,Ifthesettingvalueis500,whentheload currentoverthisvalue,Micromodulewillsendcurrentmeter reportcommandtothenodeofcorrespondingGroup.Default value=500.
Size: 2 Byte, Default Value: 500

Setting	Description
10 - 500	500*0.01=5 A

Parameter 4: Threshold of KWH for Load Caution

This is a warning when the KWh of load over the preset threshold value,Ifthesettingvalueis10000,whentheAccumulated PowerConsumptionofRelay1orRelay2overthisvalue, Micromodule will send KWh Meter Report command to the node ofcorrespondingGroup,minimumvalueis1KWhanddefault value is 10000 kWh.
Size: 2 Byte, Default Value: 10000

Setting	Description
1 - 10000	10000*1KWh=10000KWh

Parameter 5: External switch type

1.ONE PUSH BUTTONWhen the configuration setting is One Push Button, only S1 input will be valid. The control moving commands can be accepted in this switch type while the shutter is moving. In this switch type, theinclusion/exclusion/reset/associationfunctioncanalsobe fulfilled by pressing S1 just like the operation of include button. WhenS1isshortpressed,theshutterwillmoveuptoward TOP(0xFF). If during this movement S1 is short pressed again, the shutter will stop moving. A third short pressing of S1 will move the shutter down toward BOTTOM(0x00). If during this movement S1 is short pressed again, the shutter will stop moving. And so on Inverting direction and stopping.2.TWO PUSH BUTTON: (THE DEFAULT SETTING IS TWO PUSH BUTTON (2))IfthissettingisconfiguredasTwoPushButton,S1andS2 input will be valid, but will not accept pressing S1 and S2 at the sametime.Inthisswitchtype,theinclusion/exclusion/reset/association function can also be fulfilled by pressing S1 or S2 just like the operation of include button. When S1 is pressed and held more than 1.5 seconds, the shutter will move up toward TOP(0xFF), and the shutter will stop moving when S1 is released. When S2 is pressed and held for more than 1.5 seconds, the shutter will move down toward BOTTOM(0x00), and the shutter will stop moving when S2 is released.WhenS1isshortpressed,theshutterwillmoveuptoward TOP(0xFF). If during this movement S1 i short pressed again S1 again, the shutter just keep moving up toward TOP(0xFF). The easy way to stop this moving is short pressing S2. When S2 is short pressed, the shutter will move down toward BOTTON(0x00). If during this movement S2 is short pressed again S2 again, the shutter just keep moving down toward BOTTON(0x00). The easy way to stop this moving is short pressing S1. When in Two Push Button switch type, S1 or S2 are pressed and not released, and PAN08 receive any control moving command from Z-Wave RF (Ex. BASIC_SET, BINARY_SWITCH_SET, MULTILEVEL_SWITCH_SET, MULTILEVEL_SWITCH_START_LEVEL_CHANGE or MULTILEVEL_SWITCH_STOP_LEVEL_CHANGEorSCENE_ACTIVATION_SET),PAN08wontdoanychangeinpositionbut report alarm to Group1 (Alarm_Type=1, Alarm_level =0xFF), this indicate that the S1 or S2 not been release.
Size: 1 Byte, Default Value: 1

Setting	Description
1	1: One Push button
2	2:Two Push button

Parameter 6: Level report mode

Mode 1 : In 5 seconds period after controlled by a moving command, it will report the destination level when received request command. Out of the 5 seconds period, it will report the actual level of the shutter when received request command.Mode 2 : Whenever the shutter moves past a 10 percent level, it will auto report the level to Group 1 node.
Size: 1 Byte, Default Value: 2

Setting	Description
1	1:Report destination level in 5s
2	2:Report 10 percent level while running

Technical Data