LG Uplus
Smart Plug
SKU: SPES-02
Quickstart
This is a
1. Put your Z-Wave controller into inclusion mode.2. Plug the SmatPlug into the power outlet.3. Press and hold on/off button about 5 seconds.4. Orange LED will be flashing about 2 seconds, then inclusion process will be start.5. Wait until inclusion will be done.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Smart- Plug plugs in between any appliance and the AC outlet.It measures its power consumption & sends that informationto your smartphone . It can also control power sourceconnected with appliance manually and remotely usingsmartphone.
| Reset to factory default | Please use this procedure only when the network primary controller is missing or otherwise inoperable.1. Plug the SmatPlug into the power outlet.2. Press and hold on/off button about 10 seconds.3. Orange LED will be flashing about 2 seconds, then factory reset process will be start. |
| Inclusion | 1. Put your Z-Wave controller into inclusion mode.2. Plug the SmatPlug into the power outlet.3. Press and hold on/off button about 5 seconds.4. Orange LED will be flashing about 2 seconds, then inclusion process will be start.5. Wait until inclusion will be done. |
| Exclusion | 1. Put your Z-Wave controller into exclusion mode2. Plug the SmatPlug into the power outlet.3. Press and hold on/off button about 5 seconds.4. Orange LED will be flashing about 2 seconds, then exclusion process will be start.5. Wait until exclusion will be done. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus LifelineThe following Z-Wave signals may be sent to the nodes in this group: NOTIFICATION_REPORT, METER_REPORT |
Configuration Parameters
Parameter 1: standby power
First 3 Bytes : Standby Power Setting ValueLast 1 Byte : Standby Power Enable/DisableIf the value is set by 1000, standby power equals 10.00w (0x0003E8) andstandby power enable is 1.total 0x0003E801 Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | standby power disable |
| 257 - 524033 | standby power enable with 0.01 to 20.47 W Standby |
Parameter 2: meter transmit
Periodic Measurement Value Transmission Enable/Disable Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Periodic Measurement Value Transmission Enable |
| 0 | Periodic Measurement Value Transmission Disable |
Parameter 3: power accumulation mode
Power Accumulation Start/Stop Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Power Accumulation Stop |
| 1 | Power Accumulation Start |
Parameter 4: device usage
Connected Device Use / Not Use Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Connected Device Use |
| 0 | Connected Device Not Use |
Parameter 5: meter transmit interval
Periodic Measurement Value Transmission IntervalMinimum time interval : 10minutesValue : 1 (10minutes * 1) = 10minutes intervalValue : 2 (10minutes * 2) = 20minutes interval..Value : 127(10min * 72) = 720 minutes interval =>MAX Size: 1 Byte, Default Value: 6
| Setting | Description |
|---|---|
| 1 - 72 | 10min to 720 min |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 39.128 |
| Z-Wave Version | 6.61.00 |
| Certification ID | ZC10-17055591 |
| Z-Wave Product Id | 0x0247.0x0042.0x0001 |
| Supported Notification Types | Power ManagementSystem |
| Switch Type | Push Button |
| Supported Meter Type | Electric Energy |
| Firmware Updatable | Updatable by Professional/Technician |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |