ID Lock

ID Lock 101

SKU: ID-101

ZWave+ Security

Quickstart

This is a secure Door Lock - Keypad for XXXQFrequencyName. To run this device please make sure the internal battery is fully charged. To add this device to your network execute the following action:
Inclusion(Puts your device in inclusion mode) Push and hold button until all LEDs on keypad activates. (with ID Lock in an unlocked state) Release button and press 8 on keypad.Inclusion mode starts immediately. LED indicator below logo signals this by flashing blue.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

UART console communication module turns your ID Lock digital doorlock into a Z-Wave Plus enabled digital doorlock.It enables your ID Lock to operate in a Z-Wave network with numerous access control funtions and notifications.
Reset to factory default Device reset(This will reset RF interface module to factory default settings)Warning: Please do only proceed with the following reset procedure, if primary network controller is missing or otherwiseinoperable.RESET Z-WAVE MODULE:Activate doorlock service menu, by holding inside push button for 5sec while door is in OPEN state.Outside touchpanel activates > Push "0"FACTORY RESET DOORLOCK FIRMWARE:1. Push innside pushbutton continously for five Seconds after inserting batteries.2. Receive reset sound3. Receive confirmation sound
Inclusion Inclusion(Puts your device in inclusion mode) Push and hold button until all LEDs on keypad activates. (with ID Lock in an unlocked state) Release button and press 8 on keypad.Inclusion mode starts immediately. LED indicator below logo signals this by flashing blue.
Exclusion Exclusion(Puts your device in exclusion mode) Push and hold button until all LEDs on keypad activates. (with ID Lock in an unlocked state) Release button and press 8 on keypad.Exclusion mode starts immediately. LED indicator below logo signals this by flashing blue.
NIF XXXNIF
Wakeup Activate by touching numpad with two fingers or handpalm
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: Doorlock mode

Doorlock operational behaviour
Size: 1 Byte, Default Value: 0

Setting Description
3 Away mode and Automatic locking mode
0 Disabled Away mode and Manual locking mode
2 Away mode and Manual locking mode
1 Disabled Away mode and Automatic locking mode

Parameter 10: Retrieve Registered User ID information

Configuration GET for retriving UID informationRetrival of registered UIDs on parameter number 10 to 59Parameter number is representing UID indexEx. UID index 1 = parameter 10UID index 50 = parameter 59
Size: 4 Byte, Default Value: 0

Setting Description
10 - 59 RFID Card Index Number + 9

Parameter 2: RFID Configuration Set and Report

This parameter configures RFID cards to work with the door lock by setting the parameter to specific values.After setting an RFID card to the door lock, the result and configuration can be read.
Size: 2 Byte, Default Value: 0

Setting Description
1 Begin RFID Card Registration
2 RFID Registration Failed
3 Successful RFID Card Registration - 2nd byte contains Index Number
5 RFID Card Registration Mode was not started
6 RFID Card Registration Mode In Progress
4 RFID Card Registration Mode Finished

Technical Data

Hardware Platform ZM5202
Device Type Door Lock - Keypad
Network Operation Listening Sleeping Slave
Firmware Version HW: 1 FW: 1.00
Z-Wave Version 6.51.06
Certification ID ZC10-17055585
Z-Wave Product Id 0x0230.0x0030.0x0001
Supported Notification Types Access Control
Sensors Air TemperatureOpen/Closed (Binary)RF Signal StrengthVoltage
Outdoor Use ok
IP (Ingress Protection) Rated ok
Firmware Updatable Updatable by Consumer by RF
Door Lock Type Deadbolt Motor Attachment
Frequency XXfrequency
Maximum transmission power XXantenna
CEPT (Europe)Door Lock - Keypad