Quickstart
This is a
On/Off Power Switch for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.2. Once the controller is ready to Include your device, press the center button 3-5 times within 3 seconds.3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.4. The device is associated in the same group when it included in setting process. Now you can control your Z-Wave device according to groups, scenes, schedulesand automation programmed.** NOTE: If your product does not include at first, try moving the module closer to the HUB and try again -- you can move to your final location when completeFor setup instructions for your specific HUB (ie: SmartThings, Wink, Vera, etc) please go to: www.inovelli.com/nzw37-setup
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
Inovelli's Dual Smart Plug-In On/Off Module + Repeater has the ability to turn on and off appliances, lights, and more from anywhere in the world from two different outlets! In addition to the dual smart outlets, the smart plug acts as a Z-Wave signal repeater, which amplifies your Z-Wave signal, growing the capabilities of your network. This smart plug is one of the smallest plugs on the market (3.5"x2.5"x1.5") and has two (2) Z-Wave Outlets on the side of the device allowing for easy fit in compact places. You can control each outlet individually (and simultaneously*) with all HUB's that support multi-channel Z-Wave devices. Simplifying lives, one smart home product at a time... that's Inovelli.*Please see our Amazon or our website for compatible HUB's
Reset to factory default |
Use controller to remove device from network will reset it to factory default."Use this procedure only in the event that the network primary controller is missing or otherwise inoperable." |
Inclusion |
1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.2. Once the controller is ready to Include your device, press the center button 3-5 times within 3 seconds.3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.4. The device is associated in the same group when it included in setting process. Now you can control your Z-Wave device according to groups, scenes, schedulesand automation programmed.** NOTE: If your product does not include at first, try moving the module closer to the HUB and try again -- you can move to your final location when completeFor setup instructions for your specific HUB (ie: SmartThings, Wink, Vera, etc) please go to: www.inovelli.com/nzw37-setup |
Exclusion |
1. Follow the instructions for your Z-Wave certified controller to excludea device from the Z-Wave network.2. Once the controller is ready to Exclude your device, press the center button 3-5 times within 3 seconds to exclude it from the network. |
NIF |
XXXNIF |
Wakeup |
XXXWakeupDescription |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
1 |
2 |
The association group supports five nodes and lifeline function |
Technical Data
Hardware Platform |
ZM5202 |
Device Type |
On/Off Power Switch |
Network Operation |
Always On Slave |
Firmware Version |
HW: 0 FW: 20.15 |
Z-Wave Version |
6.51.06 |
Certification ID |
ZC10-17055581 |
Z-Wave Product Id |
0x0312.0xB211.0x241C |
Electric Load Type |
ELV (Electronic) |
Firmware Updatable |
Updatable by Professional/Technician |
Switch Type |
Push Button Illuminated |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |