Quickstart
This is a
Light Dimmer Switch for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.2. Once the controller is ready to include your device, quick triple press the button to include it into the network.3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.4. The device is associated in the same group when it included in setting process. Now you can control your Z-Wave device according to groups, scenes, schedules and automation programmed.** For HUB Specific Instructions, please visit: www.inovelli.com/nzw39-setup
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
Inovelli's Smart Plug-In Dimming Module + Repeater has the ability to dim & turn on and off your lights from anywhere in the world. In addition to the outlet, the smart plug acts as a Z-Wave signal repeater, which amplifies your Z-Wave signal, growing the capabilities of your network. This smart plug is one of the smallest plugs on the market (3.5"x2.5"x1.5") and has 1 Z-Wave Dimming Outlet on the side of the device allowing for easy fit in compact places. Simplifying lives, one smart home product at a time... that's Inovelli.
Reset to factory default |
Use controller to remove device from network will reset it to factory default."Use this procedure only in the event that the network primary controller is missing or otherwise inoperable." |
Inclusion |
1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.2. Once the controller is ready to include your device, quick triple press the button to include it into the network.3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.4. The device is associated in the same group when it included in setting process. Now you can control your Z-Wave device according to groups, scenes, schedules and automation programmed.** For HUB Specific Instructions, please visit: www.inovelli.com/nzw39-setup |
Exclusion |
1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.2. Once the controller is ready to Exclude your device, quick triple press the button to exclude it from the network.** For HUB Specific Instructions, please visit: www.inovelli.com/nzw39-setup |
NIF |
XXXNIF |
Wakeup |
XXXWakeupDescription |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
1 |
5 |
Theassociationgroupsupportsfivenodesandlifelinefunction |
Technical Data
Hardware Platform |
ZM5202 |
Device Type |
Light Dimmer Switch |
Network Operation |
Always On Slave |
Firmware Version |
HW: 1 FW: 20.15 |
Z-Wave Version |
6.51.06 |
Certification ID |
ZC10-17045573 |
Z-Wave Product Id |
0x0312.0xB212.0x271C |
Switch Type |
Push Button |
Color |
White |
Firmware Updatable |
Updatable by Professional/Technician |
Neutral Wire Required |
ok |
Electric Load Type |
Dimmable LEDIncandescent |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |