Quickstart
This is a
Notification Sensor for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into Add (Inclusion) mode, and following its instruction to add ZWDS01-EU to your controller. This Door/Window sensor needs to be included before installation.1. Pull the exposed plastic tab from the sensor.2. Press the button three times within 2 seconds, The Red LED indicator will be flashing three times to indicate scanning the network.3. If network is not found after 30 seconds, the sensor will go into sleep mode. To Adding again, you need repeat steps 2
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
Z-Wave Door/Window sensors are designed to secure the perimeter of the residential premise, and provide the ability to add various automation services. The Z-Wave Door/Window sensor, which consists of a magnet that attaches to a door or window, will communicate door events to the home security system. When the magnet is moved away from the sensor, a signal will be sent to the control panel that communicates the changed state to the security system. Signals can also be used to activate a chime or convenience lighting based on system settings.
| Reset to factory default |
1. Pressing the button before power on, do not release the button and power on and keep on ten seconds, and the LED will turn ON.2. After over 1 seconds the Red LED indicator will turn OFF, then go auto Adding procedure.3. IDs are excluded and all settings will reset to factory default.4. Device begin auto Adding (Inclusion) mode.Note: Use this procedure only in the event that the primary controller is lost. |
| Inclusion |
For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into Add (Inclusion) mode, and following its instruction to add ZWDS01-EU to your controller. This Door/Window sensor needs to be included before installation.1. Pull the exposed plastic tab from the sensor.2. Press the button three times within 2 seconds, The Red LED indicator will be flashing three times to indicate scanning the network.3. If network is not found after 30 seconds, the sensor will go into sleep mode. To Adding again, you need repeat steps 2 |
| Exclusion |
For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into Remove (Exclusion) mode, and following its instruction to delete ZWDS01-EU to your Z-Wave controller.1. Remove device front cover and pressing the button three times within 2 seconds, The Red LED indicator will be flashing three times and enter exclusion mode. 2. If remove (exclusion) successful, go auto Adding procedure.3. Node ID has been remove. |
| NIF |
XXXNIF |
| Wakeup |
Use Wake up command to set up the awaking time and send the wake up notification to controller.User can use command to change the auto wake up from 1 minute to 24 hours, interval increment is 1minute. Factory default is 120 minutes. |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
5 |
Battery Report; Notification Report; Device Reset Locally Notification; Sensor Binary Report. |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Notification Sensor |
| Network Operation |
Reporting Sleeping Slave |
| Firmware Version |
HW: 255 FW: 1.37 |
| Z-Wave Version |
6.51.07 |
| Certification ID |
ZC10-17045568 |
| Z-Wave Product Id |
0x0286.0x0187.0x0197 |
| Color |
White |
| Supported Notification Types |
Home Security |
| Sensors |
Open/Closed (Binary) |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
