GoControl
WS15Z5-1
SKU: WS15Z5-1
Quickstart
This is a
With your Controller in Discovery or Add Mode, tap the switch. The LED will blink slowly when in ADD Mode.You should see an indication on your Controller that the device was added tothe network and the LED will stop blinking.The device will appear in the list of Switches. It should display as a switch.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The WS15Z5-1 is a Smart in-wall switch designed providing the ideal mood for every situation forthe entire home. Not only can this switch control the connected load, with Central Scene support it can run up to 8 scenes created by the Hub, making the familiar light switch the most versatile Home Automation light switch available. It can essentially control lights and devices throughout the entire home.With Over The Air upgrading supported, this device can be seamlessly updated to the most recent firmware and software features.Finally, as a Z-Wave plus product, its 30% longer range is ideal for easily creating a strong Z-Wave mesh network for an easier installation and more reliable operation.
| Reset to factory default | To reset the WS15Z5-1 and clear all network information, follow these steps:1. Tap the top of the switch fi ve (5) times.2. Press and hold the bottom of the switch for 15 seconds. The LED will increasingly blink faster to indicate that a Reset is taking place. |
| Inclusion | With your Controller in Discovery or Add Mode, tap the switch. The LED will blink slowly when in ADD Mode.You should see an indication on your Controller that the device was added tothe network and the LED will stop blinking.The device will appear in the list of Switches. It should display as a switch. |
| Exclusion | Set the Controller into Removal Mode and follow its instruction to delete theWS15Z5-1 from the Controller.Remove the switch by tapping the paddle 2 times. The LED will begin blinkingslowly for 10 seconds indicating that it has been removed.You should see an indication on your Controller that the device was removedfrom the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Other Non-Dimming devices |
| 3 | 5 | Dimmers |
Configuration Parameters
Parameter 3: Night Light
The LED Night Light on the WS15Z5-1 will turn OFF when the load attached isturned ON.To make the LED turn ON when the load attached is turned ON. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0 - LED OFF when the load is on, and ON when the load is off.1 - LED ON when the load is on, and OFF when the load is off.2 - LED is always on.3 - LED is always off.4 - LED blinks during RF transmissions from or to the device. |
Parameter 4: Invert Switch
To change the top of the switch to OFF and the bottom of the switch ON. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0 - Top of switch is ON, bottom of switch is OFF.1 - Bottom of switch is ON, top of switch is OFF |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 1.26 |
| Z-Wave Version | 6.51.09 |
| Certification ID | ZC10-17045537 |
| Z-Wave Product Id | 0x014F.0x5753.0x3535 |
| Color | White |
| Neutral Wire Required | ok |
| Electric Load Type | Incandescent |
| Z-Wave Scene Type | Central Scene |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |