KPL MOTION SENSOR
PIR-ZWAVE
SKU: IX30-ZWAVE
Quickstart
This is a
enter the Inclusion Mode of gateway, and press the tamper switch 3 times within 1.5s, then the PIR sensor will stay in enrollment state until successfully enrolled into network or enrollment time out after 30s.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
IX30-Z-Wave is a digital micro-control intrusion detector adopting Energy Accumulation Logical Processing & Random Dynamic Time Segmentation Technology. With precise columnar Fresnel lens, IX30-Z-Wave can increase its energy receiving efficiency and sensitivity without false alarm. In conjunction with advanced software technology, it will make an accurate judgment between real intruder & interference factors that may cause false alarm. Superior ability to detect & prevent false positives.
| Reset to factory default | Press the anti-tamper switch for 6 times within 2.5 seconds to restore factory settings(Please include a request to use the resetprocedure only when the primary controller is missing or inoperable) |
| Inclusion | enter the Inclusion Mode of gateway, and press the tamper switch 3 times within 1.5s, then the PIR sensor will stay in enrollment state until successfully enrolled into network or enrollment time out after 30s. |
| Exclusion | enter the Exclusion Mode of gateway, and press the tamper switch 3 times within 1.5s, then the PIR sensor will be removed after a period of time. |
| NIF | XXXNIF |
| Wakeup | a) Manual Wake-up Quickly press tamper switch once, the PIR sensor will automatically send wake-up information, and there will be 10s after wake-up to receive gateway setting information.b) Automatic Wake-up Default time of automatic wake-up is 24 hours, and there will be 10s after wake-up to receive gateway setting information, the max automatic report time = 24 hours, minimum=30min |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | It will send NOTIFICATION_REPORTto the device in Lifeline group when the PIR sensor is triggered/recovered , tamper switch is triggered / recovered. When in low battery status, PIR sensor will send BATTERY_REPORT to Lifeline group device periodically. The PIR sensor will send DEVICE_RESET_LOCALLY_NOTIFICATION to Lifeline group device when the device recovers to factory settings. |
| 2 | 2 | When the PIR sensor is opened, it will send BASIC SET command to control these devices in Group2. |
Configuration Parameters
Parameter 1: Basic Set Level
If there is any device under Association Group2, the door sensor will send Basic Set = value command to control that device when the door sensor is opened. Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 255 | For ON/OFF Light Only |
| 1 - 100 | Dimmer Level |
Parameter 2: Turn Off Light Time
If there is any device under Association Group2, the PIR sensor will send Basic Set = value command to Group2, and send Basic Set = 0x00 command to turn-off light after 5 x t seconds Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 24 | Turn Off Light Time |
Parameter 3: PIR Sensor Alarm Elimination Time Configuration
Min set time is 5s. If the configuration is 1, that means it will eliminate alarm after 5 seconds, if t, will eliminate alarm after 5 x t seconds. Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 24 | PIR Sensor Alarm Elimination Time Configuration |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 255 FW: 5.36 |
| Z-Wave Version | 6.51.09 |
| Certification ID | ZC10-17035481 |
| Z-Wave Product Id | 0x0214.0x0002.0x0002 |
| Supported Notification Types | Home Security |
| Sensors | Motion/No Motion (Binary) |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |