Quickstart
This is a
Whole Home Meter - Simple for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. -Insert batteries to power on the E-meter. -Put the Z-Wave control panel into Inclusion mode (please refer tothe Z-Wave control panel manual). -Within 1.5 seconds, press the Function Button 3 times. -Refer to operation manual of the Z-Wave Gateway or Control Panelto complete the adding process.If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device).
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
EMD-1ZW E-Meter is a power metering device designed to measure electricity consumption from the electricity meter. E-Meter counts LED pulses from the house meter and converts it to Watt and accumulated KWh. Measuring your homes energy consumption is the first and most important step toward reducing energy consumption and achieving greater energy efficiency.
| Reset to factory default |
Factory resetting the device will restore it to factory default settings (i.e. not included into any Z-Wave network). Please only use this procedure if the Z-Wave Gateway or Control Panel is lost or otherwise inoperable. -Press and hold the Function Button of the device for 10 seconds to factory reset. |
| Inclusion |
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. -Insert batteries to power on the E-meter. -Put the Z-Wave control panel into Inclusion mode (please refer tothe Z-Wave control panel manual). -Within 1.5 seconds, press the Function Button 3 times. -Refer to operation manual of the Z-Wave Gateway or Control Panelto complete the adding process.If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see Removing Device). |
| Exclusion |
The device must be removed from existing Z-Wave network before being added into another.Exclusion Mode -Put the Z-Wave Gateway or Control Panel into Exclusion mode(please refer to the Z-Wave or control panel manual). -Within 1.5 seconds, press the Function Button 3 times and thedevice will be removed from the Z-Wave network. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
3 |
Group 1 for LifeLine:Battery CC (COMMAND_CLASS_BASIC)Device Reset Locally CC Meter CC |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Whole Home Meter - Simple |
| Network Operation |
Listening Sleeping Slave |
| Firmware Version |
HW: 255 FW: 1.37 |
| Z-Wave Version |
6.51.09 |
| Certification ID |
ZC10-17035458 |
| Z-Wave Product Id |
0x018E.0x0004.0x000C |
| Firmware Updatable |
Updatable by Professional/Technician |
| Supported Meter Type |
Electric Energy |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
