Quickstart
This is a
On/Off Power Switch for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
The Z-Wave Plus Decora Light Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controllers inclusion mode. 1)Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Decora Light Switch.2)Locate the light switch desired to be used with the Z-Wave Plus Decora Light Switch.3)Put your Z-Wave Plus Controller into add (inclusion) mode.4)Press the inclusion button on the Z-Wave Plus Decora Light Switch. (Figure 1)5)The LED on the front of the unit will turn off if successfully included into a network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
Easy to install in one minute by removing the existing switch plate and installing the Ecolink Z-Wave Plus Single Gang Decora Wireless Light Switchon the switch. No need to touch any electrical wiring.Product Specifications:For indoor use onlyOperating frequency: 908.42 MHzOperating temperature: 049C, 32120F (ambient temperature)Operating humidity 5-95% non-condensing 2 AA batteriesBattery Life: Approximatly 1 year
Reset to factory default |
The Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion |
The Z-Wave Plus Decora Light Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controllers inclusion mode. 1)Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Decora Light Switch.2)Locate the light switch desired to be used with the Z-Wave Plus Decora Light Switch.3)Put your Z-Wave Plus Controller into add (inclusion) mode.4)Press the inclusion button on the Z-Wave Plus Decora Light Switch. (Figure 1)5)The LED on the front of the unit will turn off if successfully included into a network. |
Exclusion |
1)Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.2)Press the inclusion / exclusion button on the Z-Wave Plus Decora Light Switch. |
NIF |
XXXNIF |
Wakeup |
XXXWakeupDescription |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
2 |
5 |
Z-Wave Plus Lifeline |
Technical Data
Hardware Platform |
ZM5202 |
Device Type |
On/Off Power Switch |
Network Operation |
Listening Sleeping Slave |
Firmware Version |
HW: 255 FW: 10.01 |
Z-Wave Version |
6.51.09 |
Certification ID |
ZC10-17025449 |
Z-Wave Product Id |
0x014A.0x0006.0x0001 |
Color |
White |
Firmware Updatable |
Updatable by Consumer by RF |
Switch Type |
Decorator Paddle Push |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |