Good Way Technology, Co., Ltd
Smart Meter Switch
SKU: TD13320
Quickstart
This is a
If you want to manually include the device, pressthe button for 3 times to include the device.LED Status: Blue LED Solid light.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Smart Meter switch allows controlling two independentloads both via Z-Wave wirelessly and locally utilizing atraditional wall switch. The switch is no longer directlyconnected to the load but acts as input device for the inwall switch that is controlling the load. And this devicecan calculate the total power consumption in timeperiods of day, month and year. Display the values of themeasurements on the remote site.
| Reset to factory default | The Device Reset Locally Notification Command is used toadvertise that the device will be reset to default.Press the button 3 times in 2 sec., and hold it for morethan 3 sec.Please use this procedure only when the network primarycontroller is missing or otherwise inoperable. |
| Inclusion | If you want to manually include the device, pressthe button for 3 times to include the device.LED Status: Blue LED Solid light. |
| Exclusion | If you want to manually exclude the device, pressthe button for 3 times to exclude the device.LED Status: Green LED 1 sec. flashes 1 times |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Group-1:u0022Lifelineu0022.Group-1 is used to send device status (NOTIFICATION,DEVICE_RESET_LOCALLY NOTIFICATION,BASIC_REPORT,METER_REPORT) to the controller. |
| 2 | 5 | Group-2:u0022ON/OFF controlu0022.When the device is turned on/off, a BASIC_SET Command Class will be sent to the devices in Group-2. |
| 3 | 5 | Group-3:u0022Overload alarmu0022.When over loaded ,a NOTIFICATION report will be sent to the devices in Group-3. |
Configuration Parameters
Parameter 1: Meter Report Time
How often to send a meter report(minute).Available configuration value:5-1092:5 minutes to 1092 minutes. Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 5 - 1092 | How often to send a meter report(minute). |
Parameter 2: Night light mode
Sets the night light mode.Available configuration value:0: Turn off the night light1: Turn on the night light Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | Sets the night light mode |
Parameter 3: Night light color value
Sets the night light color value.Available configuration value:0: none color1:Red2: Orange3: Green4: Blue5: Indigo6: Pink7: Light Pink Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Sets the night light color value |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 2.14 |
| Z-Wave Version | 6.51.09 |
| Certification ID | ZC10-17025434 |
| Z-Wave Product Id | 0x0068.0x0003.0x0006 |
| Supported Meter Type | Electric Energy |
| Firmware Updatable | Updatable by Manufacturer |
| Electric Load Type | ELV (Electronic) |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |